- Location
- Ferndown, Dorset
- Main postcode district
- BH22
- Nearby (straight line)
- Wimborne Minster (4 miles), Bournemouth (6 miles) and Christchurch (7 miles)
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
What should sites in Ferndown consider?
Hygiene-sensitive sites in Ferndown, such as food processors, can use dock seals to reduce the gaps through which dust and pests might enter during loading. Older seals at docks in Ferndown that have been left with split covers can soak up rain, becoming heavy and losing their shape over winter.
Weather-exposed bays in Ferndown gain the most from a well-fitted seal, since wind and rain otherwise find every gap around the trailer.
Our part of the job in Ferndown is to survey, quote and manage; the fitting itself is done by specialist installation engineers working under our management. The survey and the written quote are free. Once the fixed price is accepted, we agree dates that work around your deliveries and shifts, including out-of-hours working where needed. Every installation is tested before handover, and you receive the documentation for each item fitted.
How are dock seals fitted to a loading bay?
Dock seals are fixed to the outside wall around the dock door, normally on brackets or a frame that sets their projection, and a set usually takes a few hours to fit. No power supply is needed.
- The wall is checked for sound fixing points, with a frame or spreader plates added on cladding.
- The head pad and side pads are positioned to suit your trailer width and height.
- Projection is set relative to the bumpers, so trailers compress the foam by the right amount.
- Bumpers are checked and, if worn, replaced at the same time.
- A trailer is docked to confirm an even seal along the head and sides.
From you we need the bay taken out of use, a clear area in the yard for powered access equipment and, ideally, one of your usual trailers available at the end of the job so the fit can be checked under real conditions.
When is a dock seal a better choice than a shelter?
A dock seal is a better choice than a shelter when the trailers using a bay are consistent in size, the dock height suits them, and the tightest practical seal matters. Mixed fleets are usually better served by a shelter.
- Consistent fleets: dedicated vehicles or regular hauliers using the same trailer type.
- Temperature control: chilled or heated buildings where gaps around the trailer are costly.
- Security and hygiene: fewer gaps for pests, dust and unauthorised access during loading.
- Budget: seals cost less than inflatable shelters for a close fit.
The trade-offs are that seals can leave gaps at trailer door hinges, side pads can intrude into the trailer opening if poorly sized, and the covers wear from rubbing. If your trailers vary, compare our retractable dock shelters before deciding, as they leave the full opening clear.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Scope to convert ground-level doors into docks or add lift tables
- Access for deliveries, cranes or lifting equipment during installation
- Clear opening width and height for each door
- Yard gradient and the slope of the approach to the dock
- Control positions, isolators and any existing interlocks
- Wall and steel structure for door, shelter and bumper fixings
Options to discuss
Fixed head pad seal
A head pad and two side pads of set depth, the simplest and tightest arrangement where every trailer using the bay is the same height.
Tapered side pads
Side pads tapered in section so they guide the trailer in and intrude less into the trailer opening, which extends pad and cover life.
What do the rules in England mean for the work?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Ferndown. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock seals in Ferndown
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Ferndown, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Ferndown site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Is VAT included in your guide prices for dock seals?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Dorset as everywhere else: for dock seals, it is £1,100 to £2,600 per set, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
How can I tell if seal projection is wrong?
Look at the pads with a trailer docked. Daylight around the head or sides suggests too little compression, while pads squashed flat or bulging around the trailer suggest too much. Worn bumpers are a common cause, and both can be checked at a planned service.
Can just the covers be replaced?
Yes, if the foam is still resilient and dry, new covers can often be fitted over the existing foam, which usually costs less than new pads. Waterlogged or permanently crushed foam should be replaced. Cover replacement is handled as a repair, with the visit price agreed beforehand.
Dock seals near Ferndown
The same survey, quote and repair service is available in towns around Ferndown, such as Wimborne Minster (4 miles), Bournemouth (6 miles) and Christchurch (7 miles).
Other loading bay services in Ferndown
Full guide to dock seals · Everything we do in Ferndown
Have photos of the door, leveller or shelter? Send them with your enquiry and we can give a clearer answer for your Ferndown site.