- Location
- March, Cambridgeshire
- Main postcode district
- PE15
- Nearby (straight line)
- Wisbech (8 miles), Ely (13 miles) and Peterborough (14 miles)
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
Is this right for your site in March?
Older seals at docks in March that have been left with split covers can soak up rain, becoming heavy and losing their shape over winter. Before recommending seals for a bay in March, we check how consistent your trailers are, because mixed fleets are usually better served by a shelter.
Own-fleet distribution sites in March, where the same trailers arrive day after day, are well suited to foam dock seals and the tight fit they give.
Keeping the dock running is usually the first concern, so we plan around it. After a free survey of your March site and a written quote at a fixed price, we agree when each bay can be released and whether any work should happen out of hours. Specialist installation engineers working under our management then fit the equipment, and we test it and hand over the documentation before the bay goes back into use.
How are dock seals fitted to a loading bay?
Dock seals are fixed to the outside wall around the dock door, normally on brackets or a frame that sets their projection, and a set usually takes a few hours to fit. No power supply is needed.
- The wall is checked for sound fixing points, with a frame or spreader plates added on cladding.
- The head pad and side pads are positioned to suit your trailer width and height.
- Projection is set relative to the bumpers, so trailers compress the foam by the right amount.
- Bumpers are checked and, if worn, replaced at the same time.
- A trailer is docked to confirm an even seal along the head and sides.
From you we need the bay taken out of use, a clear area in the yard for powered access equipment and, ideally, one of your usual trailers available at the end of the job so the fit can be checked under real conditions.
How can dock seal pads be made to last longer?
Dock seal pads last longer when trailers arrive straight and stop at the right point, because most wear comes from trailers rubbing against the covers or pressing too far into the foam. Covers usually wear first, and the foam inside can outlast them.
- Replaceable wear pleats: sacrificial strips on the pad faces take the abrasion and can be swapped cheaply.
- Wheel guides and dock lights: help drivers reverse squarely into the centre of the bay.
- Bumper maintenance: keeps compression within design limits.
- Tapered side pads: guide trailers in and reduce rubbing on the pad edges.
- Driver briefings: regular hauliers who know the bay damage it less.
When covers split, replacing them promptly stops rain soaking into the foam, which makes it heavy, slow to recover and prone to freezing in winter.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Condition of any existing leveller pit, kerb angles and pit drainage
- Headroom above the opening and which track type will suit it
- Escape routes and pedestrian doors close to the bay
- Whether planning, building control or a building warrant may be needed
- Dock height and the mix of trailers you load
- Drainage on recessed or sloping dock approaches
Options to discuss
Fixed head pad seal
A head pad and two side pads of set depth, the simplest and tightest arrangement where every trailer using the bay is the same height.
Replaceable wear pleats
Sacrificial fabric strips on the pad faces that take the rubbing from trailers and can be replaced without changing the whole cover.
Which rules apply in England?
Sites in March fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about dock seals in March
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your March site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
What details do you need from us to quote for dock seals?
To get started, send the site address in March, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
How do you price dock seals for a site in March?
Guide budgets for supply and fit are £1,100 to £2,600 per set, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Do trailer doors need to be opened before docking against a seal?
Yes, the rear doors are opened and folded back before the trailer reverses onto a seal, so the pads press against the rear of the trailer rather than the doors. Gaps can remain at the door hinges, which is a known limitation of seals compared with shelters.
Do dock seals block access to the trailer?
They can if they are poorly sized. Side pads that sit inside the line of the trailer body intrude into the opening and get in the way of pallets and forklifts. Correctly sized and tapered pads compress against the rear corners and leave the opening clear.
Dock seals near March
If your site is not in March itself, it may be near one of these: Wisbech (8 miles), Ely (13 miles) and Peterborough (14 miles). Pick the closest.
Other loading bay services in March
Full guide to dock seals · Everything we do in March
Call us or request a quote online to talk through loading bay work at your site in March.