- Location
- Leek, Staffordshire
- Main postcode district
- ST13
- Nearby (straight line)
- Biddulph (6 miles), Congleton (9 miles) and Kidsgrove (9 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Where does this fit at a dock in Leek?
Tight yards in Leek where drivers reverse between parked trailers or around buildings make wheel guides especially useful for getting the trailer straight first time. Resurfacing works on a yard in Leek are an ideal moment to fit cast-in wheel guides, before the concrete is finished and bays come back into use.
On older estates around Leek, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler.
A single contact at Loading Bay Doors handles your project in Leek from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
Which type of dock light is best for a loading bay?
An LED swing-arm dock light is the usual choice for a loading bay, because it reaches into the trailer during loading and folds back flat against the wall when the bay is closed. LED heads run much cooler than older lamps and cope better with knocks and vibration.
- Arm length: longer arms push light further into deep trailers, but need clear wall space so they can fold away from the door path.
- Rigid or flexible arm: a rigid arm with a pivoting head is tougher; a flexible section can be easier to aim.
- Guarding: a protective cage or polycarbonate cover helps the head survive forklift contact.
- Switching: a switch on the head or on the wall, or linked to the door so the light comes on as it opens.
- Supply voltage: mains or low-voltage, confirmed at survey to suit your site.
The light is mounted inside the building beside the door, clear of the door tracks, at a height that lets it swing over the leveller and into the trailer.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Working hours, shift patterns and windows for out-of-hours work
- Access for deliveries, cranes or lifting equipment during installation
- Wind exposure at the dock, which affects door and shelter choice
- Traffic routes for vehicles and separation of pedestrians
- Bumper position and wear or damage on the dock face
- Gaps around trailers where heated or chilled air escapes
Options to discuss
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Regulations and approvals in England
Sites in Leek fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about dock lights and wheel guides in Leek
Can you work outside our normal operating hours in Leek?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Can you work alongside our main contractor on a new build in Leek?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Is VAT included in your guide prices for dock lights and wheel guides?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Staffordshire as everywhere else: for dock lights and wheel guides, it is £280 to £950 per item, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Do wheel guides damage tyres?
Correctly spaced wheel guides should not damage tyres. They are set slightly wider than the trailer track so the tyre only brushes the guide when the trailer is off line, and a flared entry stops tyres hitting the end. Guides that are bent or set too narrow should be corrected.
Are LED dock lights better than older lamps?
LED dock lights are generally the better choice. They run much cooler, so there is less risk of heat damage to goods or packaging close to the head, they cope well with vibration, and they reach full brightness straight away. They also use less electricity for the same light, although savings depend on how long the lights are on.
Dock lights and wheel guides near Leek
Businesses outside Leek may find their nearest town in this list: Biddulph (6 miles), Congleton (9 miles) and Kidsgrove (9 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Leek
Full guide to dock lights and wheel guides · Everything we do in Leek
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Leek.