- Location
- Perth, Perth and Kinross
- Main postcode district
- PH1
- Nearby (straight line)
- Blairgowrie (14 miles), Crieff (16 miles) and Glenrothes (17 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
What matters for dock lights and wheel guides in Perth?
Tight yards in Perth where drivers reverse between parked trailers or around buildings make wheel guides especially useful for getting the trailer straight first time. Warehouses in Perth loading deep trailers by forklift often find the back of the load hard to see without a dock light reaching into the trailer.
On older estates around Perth, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler.
How does an installation in Perth work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
How much do dock lights and wheel guides cost?
Dock lights and wheel guides typically cost £280 to £950 per item, supplied and fitted, excluding VAT, where an item is one dock light or one wheel guide. A standard LED swing-arm light usually sits in the lower half of the range; long, heavy-section or cast-in guides sit towards the top.
What moves the price:
- Light specification: arm length, LED head output, protective guarding and whether a low-voltage supply is needed.
- Power: the distance to a suitable supply and how the cable is contained.
- Guide length and section: longer guides and heavier steel cost more.
- Yard surface: sound concrete takes anchors directly; tarmac usually needs a concrete base first, priced after survey.
- Number of bays: fitting several bays in one visit lowers the cost per item.
These are guide budgets. After a free site survey we send a written quote, which is the fixed price. VAT is added at the standard rate.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Age and condition of the equipment already in place
- Clear opening width and height for each door
- Wall and steel structure for door, shelter and bumper fixings
- Scope to convert ground-level doors into docks or add lift tables
- How often each door cycles during a typical shift
- How drivers are prevented from pulling away too early
Options to discuss
LED swing-arm dock light
An LED head on a swing arm beside the door, swung into the trailer during loading and folded back flat against the wall when the bay is closed.
Bolt-down wheel guides
Steel tube or channel guides fixed with resin anchors into an existing concrete apron, typically galvanised or painted in high-visibility colours for drivers using mirrors.
Planning, building control and safety law in Scotland
In Scotland, building work such as forming a new opening or a dock leveller pit may need a building warrant from the local authority before it starts. For sites in Perth, external structures such as loading houses or canopies may also need planning permission from the council. We check what applies at survey and factor any approvals into the programme.
Questions about dock lights and wheel guides in Perth
What details do you need from us to quote for dock lights and wheel guides?
To get started, send the site address in Perth, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Is the site survey in Perth free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Can you work outside our normal operating hours in Perth?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Can dock lights be fitted without stopping loading?
Usually yes. Dock lights are fitted from inside the building beside the door, and the bay can often keep working except for a short period while the supply is isolated and connected. We agree timings with you so the work fits around trailer arrivals.
Do wheel guides damage tyres?
Correctly spaced wheel guides should not damage tyres. They are set slightly wider than the trailer track so the tyre only brushes the guide when the trailer is off line, and a flared entry stops tyres hitting the end. Guides that are bent or set too narrow should be corrected.
Dock lights and wheel guides near Perth
Nearby places we cover, measured from Perth, include Blairgowrie (14 miles), Crieff (16 miles) and Glenrothes (17 miles). Ask if your own town is missing.
Other loading bay services in Perth
Full guide to dock lights and wheel guides · Everything we do in Perth
Start your enquiry for Perth through the quote tool. A few photos and approximate sizes help us respond with something useful.