- Location
- Crieff, Perth and Kinross
- Main postcode district
- PH7
- Nearby (straight line)
- Perth (16 miles), Alloa (18 miles) and Stirling (18 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Where does this fit at a dock in Crieff?
A landlord preparing a unit in Crieff for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical. Shelters and seals at sites near Crieff last longer when wheel guides keep trailers centred, because off-centre parking is a common cause of torn curtains.
Resurfacing works on a yard in Crieff are an ideal moment to fit cast-in wheel guides, before the concrete is finished and bays come back into use.
If you are planning dock lights and wheel guides for a site in Crieff, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
Should wheel guides be bolted down or cast in?
Wheel guides are bolted down on an existing sound concrete yard and cast in where new concrete is being laid. Both give a strong fixing; the choice depends on whether the yard is being resurfaced.
- Bolt-down guides: steel tube or channel fixed with resin anchors. Quick to fit to existing bays and easy to replace if damaged.
- Cast-in guides: set into fresh concrete with embedded anchors, suited to new-build docks and conversions.
- Flared entry: an angled lead-in at the yard end catches the wheel early and steers it into line.
- Finish: typically galvanised, or painted yellow and black so drivers can see them in mirrors.
Guides are set out to suit the track width of the trailers you receive, centred on the leveller, and long enough to straighten the trailer before it reaches the bumpers. Tarmac is usually too soft to hold anchors, so a concrete strip or base is laid first. Our guide to choosing dock bumpers and wheel guides covers layout in more depth.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Clear opening width and height for each door
- Age and condition of the equipment already in place
- Dock height and the mix of trailers you load
- How often each door cycles during a typical shift
- How drivers are prevented from pulling away too early
- Access for deliveries, cranes or lifting equipment during installation
Options to discuss
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Bolt-down wheel guides
Steel tube or channel guides fixed with resin anchors into an existing concrete apron, typically galvanised or painted in high-visibility colours for drivers using mirrors.
Regulations and approvals in Scotland
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Crieff. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Questions about dock lights and wheel guides in Crieff
Is the site survey in Crieff free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
How long does installation take at a site in Crieff?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Can you work alongside our main contractor on a new build in Crieff?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Where should a dock light be mounted?
A dock light is mounted inside the building beside the door opening, high enough to swing over the leveller and into the trailer. It must fold back flat against the wall, clear of the door tracks and the forklift route, so it is not struck when the bay is not in use.
Dock lights and wheel guides near Crieff
Close neighbours of Crieff with their own pages here: Perth (16 miles), Alloa (18 miles) and Stirling (18 miles). Choose one to see coverage details for that town.
Other loading bay services in Crieff
Full guide to dock lights and wheel guides · Everything we do in Crieff
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Crieff site.