- Location
- Milford Haven, Dyfed
- Main postcode district
- SA73
- Nearby (straight line)
- Pembroke Dock (4 miles) and Haverfordwest (7 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
What should sites in Milford Haven consider?
On older estates around Milford Haven, dock lights may still use outdated lamps, and an LED swing-arm light is a simple upgrade that runs cooler. Tight yards in Milford Haven where drivers reverse between parked trailers or around buildings make wheel guides especially useful for getting the trailer straight first time.
Parcel and retail distribution operators in Milford Haven that work into the evening rely on good lighting inside trailers once daylight at the dock fades.
We never ask you to commit before you have a fixed price. A free survey at your Milford Haven site comes first, followed by a written quote. When the order goes ahead, we plan the installation around your operation, book any out-of-hours working you need and manage the specialist installation engineers on site. The job ends with a full test, a run-through for the people who will use the equipment and a set of handover documents.
Should wheel guides be bolted down or cast in?
Wheel guides are bolted down on an existing sound concrete yard and cast in where new concrete is being laid. Both give a strong fixing; the choice depends on whether the yard is being resurfaced.
- Bolt-down guides: steel tube or channel fixed with resin anchors. Quick to fit to existing bays and easy to replace if damaged.
- Cast-in guides: set into fresh concrete with embedded anchors, suited to new-build docks and conversions.
- Flared entry: an angled lead-in at the yard end catches the wheel early and steers it into line.
- Finish: typically galvanised, or painted yellow and black so drivers can see them in mirrors.
Guides are set out to suit the track width of the trailers you receive, centred on the leveller, and long enough to straighten the trailer before it reaches the bumpers. Tarmac is usually too soft to hold anchors, so a concrete strip or base is laid first. Our guide to choosing dock bumpers and wheel guides covers layout in more depth.
How do wheel guides protect shelters, seals and levellers?
Wheel guides protect dock equipment by keeping every trailer centred on the bay, so contact forces land where the equipment is designed to take them. A trailer that parks off-centre loads one side of the dock much harder than the other.
- Shelters: off-centre trailers catch the side curtains and frame, causing tears and bent arms.
- Seals: one pad is crushed while the other barely touches, leaving gaps for draughts and rain.
- Levellers: the lip can land near the edge of the trailer bed, with less support for forklifts.
- Bumpers: one bumper takes every impact and wears out early.
Dock lights help in a different way: forklift drivers who can see clearly inside the trailer are less likely to strike the trailer walls or the door frame on the way out. Combining guides and lights with correctly positioned dock bumpers gives a well-protected bay.
The same published guide range applies across Wales; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Whether planning, building control or a building warrant may be needed
- Clear opening width and height for each door
- Access for deliveries, cranes or lifting equipment during installation
- How drivers are prevented from pulling away too early
- How often each door cycles during a typical shift
- Wall and steel structure for door, shelter and bumper fixings
Options to discuss
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
Bolt-down wheel guides
Steel tube or channel guides fixed with resin anchors into an existing concrete apron, typically galvanised or painted in high-visibility colours for drivers using mirrors.
Planning, building control and safety law in Wales
Equipment fitted in Wales may carry the UKCA or the CE mark. For each door, leveller or shelter installed in Milford Haven, we hand over the documentation that comes with it. Permissions are never assumed either way: whether planning permission or Building Regulations approval is needed, we check what applies at survey and tell you before dates are agreed.
Questions about dock lights and wheel guides in Milford Haven
Can you work alongside our main contractor on a new build in Milford Haven?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Which building and safety rules apply to a site in Milford Haven?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Milford Haven, we check what applies at survey and design to it.
Is VAT included in your guide prices for dock lights and wheel guides?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Dyfed as everywhere else: for dock lights and wheel guides, it is £280 to £950 per item, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Where should a dock light be mounted?
A dock light is mounted inside the building beside the door opening, high enough to swing over the leveller and into the trailer. It must fold back flat against the wall, clear of the door tracks and the forklift route, so it is not struck when the bay is not in use.
How long should wheel guides be?
Wheel guides need to be long enough to straighten the trailer before it reaches the bumpers, and the right length depends on your yard and approach. Tight yards where drivers turn late usually need longer guides with a flared entry. We set the length and spacing at survey.
Dock lights and wheel guides near Milford Haven
Close neighbours of Milford Haven with their own pages here: Pembroke Dock (4 miles) and Haverfordwest (7 miles). Choose one to see coverage details for that town.
Other loading bay services in Milford Haven
Full guide to dock lights and wheel guides · Everything we do in Milford Haven
Start your enquiry for Milford Haven through the quote tool. A few photos and approximate sizes help us respond with something useful.