- Location
- Lancing, West Sussex
- Main postcode districts
- BN15 and BN43
- Nearby (straight line)
- Shoreham-by-Sea (2 miles), Worthing (2 miles) and Portslade (5 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
How does this suit sites in Lancing?
Older units in Lancing may still run mechanical or early hydraulic levellers, where a well-judged repair can keep the bay working before replacement is needed. Distribution docks in Lancing that run several shifts put heavy cycles through leveller hydraulics, so leaks and slow operation can show up sooner.
Low temperatures at chilled and frozen docks in Lancing can affect hydraulic oil and seals, so it helps to mention the operating temperature when reporting a fault.
Every visit to a site in Lancing begins with an agreed price. The charge is confirmed in writing before an engineer attends, so the cost is clear from the outset. Photos of the fault, the data plate and the surrounding area make diagnosis easier. Extra work found during the visit is priced and approved before it is done. A written report then sets out what was found, what was fixed and what still needs attention.
What happens on site during a dock leveller repair?
During a leveller repair the bay is closed, the leveller is isolated and propped, and the engineer works from the pit or deck to diagnose and repair the fault. Neighbouring bays normally keep working.
- Close the bay: no trailer on the dock, the door closed and forklifts kept away.
- Isolate and prop: the leveller is electrically isolated and locked off, and the platform raised and supported on its maintenance strut before anyone goes underneath.
- Clean and inspect: debris and spilt oil are cleared from the pit so the fault can be traced.
- Repair: parts are fitted or welded. Anything beyond the agreed scope is quoted first.
- Test: the leveller is cycled, the lip checked and controls tested before the bay reopens.
It helps if you can provide a clear bay, a contact on site, photos or labels showing the leveller type and size, and any insurer inspection report that lists the defect.
Should a dock leveller be repaired or replaced?
A dock leveller is usually worth repairing when the platform, lip and hinges are structurally sound and the fault is in the hydraulics, controls or a single component. Replacement is worth considering when the structure is fatigued or the leveller no longer suits your trailers.
Repair is likely to be the better option when:
- the fault is a hose, cylinder, valve or power pack;
- lip or hinge damage is limited to one area and can be welded or rebuilt;
- the leveller is the right length for your trailer height range.
Replacement is worth pricing when:
- the deck or hinge structure is cracking in several places;
- hydraulic failures keep recurring despite repairs;
- an old mechanical leveller needs major parts that are hard to find;
- trailers now arrive at heights the leveller cannot reach at a safe gradient.
Our guide to dock leveller repair or replace covers the signs in more detail.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What we look at around the bay
- Leveller toe guards and side skirting, where fitted
- Pit frame welds, platform cracks and structural damage
- Dock bumpers for missing rubber or loose fixings
- Manual override and emergency operation on powered doors
- Track alignment, rollers and wall fixings
- Door panels, side seals and bottom rubbers
Options to discuss
Hydraulic repairs
Cylinders resealed or replaced, hoses and fittings renewed, check and safety valves tested, and the system refilled with fresh oil and bled so the platform moves smoothly again.
Structural and weld repairs
Cracked deck plates, broken welds and damaged front sections repaired by welding or with fabricated replacement parts, restoring the platform's strength.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Lancing, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies before any work starts and design the bay accordingly.
Questions about dock leveller repairs in Lancing
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
How often should equipment at our Lancing site be serviced?
It depends on how hard the equipment works and on the manufacturer's recommendations. A multi-shift dock with frequent trailer movements needs more attention than a door that opens a few times a day. We suggest a schedule after looking at the equipment and how it is used, and we can line visits up with your insurance inspections where that helps.
How is a repair or service visit in Lancing priced?
Repair and service visits are chargeable, and the price is agreed in writing before anyone attends. For dock leveller repairs, the guide budget is £220 to £2,600 per repair, excluding VAT. The exact figure depends on the fault, parts, access and timing. If the engineer finds further work on the day, it is quoted for your approval before it is carried out.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Will the repair clear an insurer's defect notice?
A repair addresses the defect listed, and our written report records what was found and what was done, which you can keep with the insurer's report. Whether the insurer needs to re-inspect is between you and them. Any further defects found during the repair are quoted before work.
Dock leveller repairs near Lancing
Businesses outside Lancing may find their nearest town in this list: Shoreham-by-Sea (2 miles), Worthing (2 miles) and Portslade (5 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Lancing
Full guide to dock leveller repairs · Everything we do in Lancing
Request a quote for your loading bay in Lancing, attaching photos of the dock, the equipment and any damage.