Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Why do sites in Perth and Kinross choose this?
Distribution docks in Perth and Kinross that run several shifts put heavy cycles through leveller hydraulics, so leaks and slow operation can show up sooner. Insurer inspections at sites around Perth and Kinross may list leveller defects that need attention, and we can price each item directly from the report.
Docks in Perth and Kinross receiving trailers at widely varying bed heights can wear lip hinges faster, and hinge rebuilds are a routine part of leveller repair.
Tell us what has gone wrong at your Perth and Kinross site and, if you can, send photos of the fault and any labels on the equipment. We then confirm the visit price in writing, and nobody attends until you have agreed it. On site, the engineer diagnoses and repairs what was agreed; anything extra is quoted first, never added without your say-so. A written report follows, covering findings, work carried out and recommendations.
Can you repair defects listed on an insurer inspection report?
Yes. Repairing defects from an engineering insurer's inspection report is one of the most common reasons for a leveller repair visit. Sending us the report is the quickest way to get an accurate price.
How it works:
- Send the report: we read each defect against the leveller it refers to, with any photos you can add.
- Price each item: we agree the visit price in writing, listing the defects it covers.
- Repair: the engineer carries out the listed repairs, and any further defects found are quoted before work.
- Record: the written report shows which defects were cleared and how, which you can keep with the insurer's report.
Any re-inspection by the insurer is arranged between you and them. If a defect is marked as dangerous, the leveller should stay out of use until it has been repaired.
Grouping several levellers' defects into one visit usually keeps the cost per item down.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
Towns we cover in Perth and Kinross
We take enquiries about dock leveller repairs from across Perth and Kinross. These are the towns with their own pages:
The visit price is agreed before anyone attends. All guide prices.
Regulations and approvals in Scotland
HSE is the workplace safety regulator in Scotland. At a loading bay in Perth and Kinross, doors need to satisfy regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, dock equipment must be kept safe under PUWER, and drivers must be prevented from pulling away too early. We check what applies before any work starts.
Questions
Do you provide a written report after each visit?
Yes. After every repair or service visit to a site in Perth and Kinross, you receive a written report setting out what was checked, what was found, what work was carried out and anything that still needs attention, with a quote for further work where needed. The report is useful for your maintenance records and for discussions with your insurer or inspector.
How often should equipment at our Perth and Kinross site be serviced?
It depends on how hard the equipment works and on the manufacturer's recommendations. A multi-shift dock with frequent trailer movements needs more attention than a door that opens a few times a day. We suggest a schedule after looking at the equipment and how it is used, and we can line visits up with your insurance inspections where that helps.
How is the price for a leveller repair agreed?
You describe the fault and send photos, and we agree the visit price in writing before anyone attends. If the engineer finds more work is needed, it is quoted and only carried out once you approve it. The visit is chargeable, and the price is always agreed first.
Can leveller repairs be done outside operating hours?
Yes, leveller repairs can be arranged for evenings or weekends where that suits your operation. Out-of-hours working costs more, and that is included in the visit price agreed in writing beforehand. Timing for each repair is agreed with you, and neighbouring bays can usually keep working.
Other services in Perth and Kinross
Full guide to dock leveller repairs · All loading bay services in Perth and Kinross