- Location
- Lerwick, Orkney, Shetland and the Western Isles
- Main postcode district
- ZE1
- Nearby (straight line)
- Remote location, covered by arrangement
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Where does this fit at a dock in Lerwick?
When a leveller at a warehouse near Lerwick sinks under load, it should be taken out of use until the hydraulic cause has been found and fixed. Older units in Lerwick may still run mechanical or early hydraulic levellers, where a well-judged repair can keep the bay working before replacement is needed.
Every leveller repair enquiry from Lerwick starts with you describing the fault, then a visit price agreed in writing before an engineer attends.
Our repair process in Lerwick has four parts. You describe the problem and send photos. We price the visit and confirm it in writing. The engineer attends, carries out the agreed work and quotes anything additional before doing it. You then receive a written report on the condition of the equipment and the work completed, which is useful for insurers, inspectors and your own planning.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
How much does a dock leveller repair cost?
A dock leveller repair typically costs £220 to £2,600 per repair, excluding VAT. Replacing a hose or limit switch sits towards the lower end; a new power pack, cylinder set or rebuilt lip hinge sits towards the top.
How the price is agreed:
- You describe the fault, ideally with photos of the leveller, the pit and any labels.
- We agree the visit price in writing before anyone attends.
- Anything found on site beyond that scope is quoted and approved by you before it is done.
What moves the price:
- Parts: cylinders, power packs, valves and hinge components vary widely in cost.
- Welding and fabrication: cracked decks, broken hinge knuckles and bent lips take more time.
- Hydraulic work: an oil change and bleeding the system add to cylinder or hose repairs.
- Pit condition: heavy debris or standing water must be cleared first.
- Out-of-hours working and location: both are agreed in the visit price.
VAT is added at the standard rate.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What we look at around the bay
- Door panels, side seals and bottom rubbers
- Hydraulic oil level, hoses and cylinders for leaks
- Manual override and emergency operation on powered doors
- Anti-fall device on upward-opening doors
- Pit frame welds, platform cracks and structural damage
- Inflatable shelter fans, airbags and control function
Options to discuss
Lip and hinge repairs
Seized or worn lip hinges rebuilt, hinge pins replaced, bent lips straightened or replaced, and lip cylinders repaired so the lip extends fully on to the trailer bed.
Control and safety repairs
Control panels, push buttons, limit switches, maintenance struts, toe guards and side skirts repaired or replaced so the leveller operates and parks safely.
Which rules apply in Scotland?
Lift tables at Scottish sites are lifting equipment under LOLER, which means thorough examination at least every 12 months, or every 6 months if people are lifted, depending on the equipment and its use. For a site in Lerwick, your insurer or competent person will confirm the interval, and we check what applies before any work starts.
If equipment needs attention at a site in Lerwick, the visit is arranged in advance and its price, including travel and any accommodation, is agreed before anyone sets off. Photos from your team help us bring the right parts first time.
Questions about dock leveller repairs in Lerwick
How often should equipment at our Lerwick site be serviced?
It depends on how hard the equipment works and on the manufacturer's recommendations. A multi-shift dock with frequent trailer movements needs more attention than a door that opens a few times a day. We suggest a schedule after looking at the equipment and how it is used, and we can line visits up with your insurance inspections where that helps.
Can you repair all makes of loading bay equipment?
We work on common makes and types of doors, dock levellers, shelters, seals and restraints. Parts availability varies, particularly for older or discontinued equipment, so it helps to send the make, model and photos of any data plates from your site in Lerwick. If original parts are not available, we tell you and price the alternatives, including replacement where that makes more sense.
Can repairs be carried out outside our working hours?
Yes, by arrangement. Evening, night or weekend visits can be booked so that repairs and servicing at your Lerwick site cause less disruption to loading. Out-of-hours attendance usually affects the price, so we include it when we agree the visit charge in writing. Tell us your shift pattern and the times when the dock is quietest.
Can leveller repairs be done outside operating hours?
Yes, leveller repairs can be arranged for evenings or weekends where that suits your operation. Out-of-hours working costs more, and that is included in the visit price agreed in writing beforehand. Timing for each repair is agreed with you, and neighbouring bays can usually keep working.
Is it safe to keep using a leaking dock leveller?
No. A dock leveller leaking hydraulic oil should be taken out of use until it has been checked, because the leak may affect how the platform holds its position under load. Oil in the pit is also a slip and environmental hazard. Describe the leak and send photos so we can plan the repair.
Dock leveller repairs near Lerwick
Other loading bay services in Lerwick
Full guide to dock leveller repairs · Everything we do in Lerwick
Call us or request a quote online to talk through loading bay work at your site in Lerwick.