- Location
- Burnley, Lancashire
- Main postcode district
- BB11
- Nearby (straight line)
- Nelson (3 miles), Colne (5 miles) and Accrington (6 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Why do sites in Burnley choose this?
Distribution docks in Burnley that run several shifts put heavy cycles through leveller hydraulics, so leaks and slow operation can show up sooner. Insurer inspections at sites around Burnley may list leveller defects that need attention, and we can price each item directly from the report.
When a leveller at a warehouse near Burnley sinks under load, it should be taken out of use until the hydraulic cause has been found and fixed.
We do not turn up and then name a price. Every repair or service visit in Burnley is agreed in writing first, including what the charge covers. Sending photos of the damage, error codes or leaks helps us diagnose the problem before travelling and bring the likely parts. Any additional work found on the day is quoted for your approval before it starts. You then get a written report for your records.
What happens on site during a dock leveller repair?
During a leveller repair the bay is closed, the leveller is isolated and propped, and the engineer works from the pit or deck to diagnose and repair the fault. Neighbouring bays normally keep working.
- Close the bay: no trailer on the dock, the door closed and forklifts kept away.
- Isolate and prop: the leveller is electrically isolated and locked off, and the platform raised and supported on its maintenance strut before anyone goes underneath.
- Clean and inspect: debris and spilt oil are cleared from the pit so the fault can be traced.
- Repair: parts are fitted or welded. Anything beyond the agreed scope is quoted first.
- Test: the leveller is cycled, the lip checked and controls tested before the bay reopens.
It helps if you can provide a clear bay, a contact on site, photos or labels showing the leveller type and size, and any insurer inspection report that lists the defect.
Can you repair defects listed on an insurer inspection report?
Yes. Repairing defects from an engineering insurer's inspection report is one of the most common reasons for a leveller repair visit. Sending us the report is the quickest way to get an accurate price.
How it works:
- Send the report: we read each defect against the leveller it refers to, with any photos you can add.
- Price each item: we agree the visit price in writing, listing the defects it covers.
- Repair: the engineer carries out the listed repairs, and any further defects found are quoted before work.
- Record: the written report shows which defects were cleared and how, which you can keep with the insurer's report.
Any re-inspection by the insurer is arranged between you and them. If a defect is marked as dangerous, the leveller should stay out of use until it has been repaired.
Grouping several levellers' defects into one visit usually keeps the cost per item down.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What we look at around the bay
- Track alignment, rollers and wall fixings
- Safety edges, photocells and light curtains
- Shelter curtains, frames and side pads for tears
- Hydraulic oil level, hoses and cylinders for leaks
- Leveller toe guards and side skirting, where fitted
- Manual override and emergency operation on powered doors
Options to discuss
Structural and weld repairs
Cracked deck plates, broken welds and damaged front sections repaired by welding or with fabricated replacement parts, restoring the platform's strength.
Hydraulic repairs
Cylinders resealed or replaced, hoses and fittings renewed, check and safety valves tested, and the system refilled with fresh oil and bled so the platform moves smoothly again.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Burnley, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies before any work starts and design the bay accordingly.
Questions about dock leveller repairs in Burnley
Can repairs be carried out outside our working hours?
Yes, by arrangement. Evening, night or weekend visits can be booked so that repairs and servicing at your Burnley site cause less disruption to loading. Out-of-hours attendance usually affects the price, so we include it when we agree the visit charge in writing. Tell us your shift pattern and the times when the dock is quietest.
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
Can you take over our existing loading bay maintenance arrangement?
Yes. Send us a list of the equipment at your Burnley site, with makes, models and approximate ages if known, plus recent service or inspection reports. We will propose a planned maintenance schedule and price it per item per visit. The first visit records the condition of everything, so you have a clear starting point for future servicing.
How is the price for a leveller repair agreed?
You describe the fault and send photos, and we agree the visit price in writing before anyone attends. If the engineer finds more work is needed, it is quoted and only carried out once you approve it. The visit is chargeable, and the price is always agreed first.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Dock leveller repairs near Burnley
The same survey, quote and repair service is available in towns around Burnley, such as Nelson (3 miles), Colne (5 miles) and Accrington (6 miles).
Other loading bay services in Burnley
Full guide to dock leveller repairs · Everything we do in Burnley
Request a quote for your loading bay in Burnley, attaching photos of the dock, the equipment and any damage.