- Location
- Bordon, Hampshire
- Main postcode district
- GU35
- Nearby (straight line)
- Alton (5 miles), Haslemere (7 miles) and Farnham (7 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Is this right for your site in Bordon?
Older units in Bordon may still run mechanical or early hydraulic levellers, where a well-judged repair can keep the bay working before replacement is needed. Low temperatures at chilled and frozen docks in Bordon can affect hydraulic oil and seals, so it helps to mention the operating temperature when reporting a fault.
Every leveller repair enquiry from Bordon starts with you describing the fault, then a visit price agreed in writing before an engineer attends.
We do not turn up and then name a price. Every repair or service visit in Bordon is agreed in writing first, including what the charge covers. Sending photos of the damage, error codes or leaks helps us diagnose the problem before travelling and bring the likely parts. Any additional work found on the day is quoted for your approval before it starts. You then get a written report for your records.
How much does a dock leveller repair cost?
A dock leveller repair typically costs £220 to £2,600 per repair, excluding VAT. Replacing a hose or limit switch sits towards the lower end; a new power pack, cylinder set or rebuilt lip hinge sits towards the top.
How the price is agreed:
- You describe the fault, ideally with photos of the leveller, the pit and any labels.
- We agree the visit price in writing before anyone attends.
- Anything found on site beyond that scope is quoted and approved by you before it is done.
What moves the price:
- Parts: cylinders, power packs, valves and hinge components vary widely in cost.
- Welding and fabrication: cracked decks, broken hinge knuckles and bent lips take more time.
- Hydraulic work: an oil change and bleeding the system add to cylinder or hose repairs.
- Pit condition: heavy debris or standing water must be cleared first.
- Out-of-hours working and location: both are agreed in the visit price.
VAT is added at the standard rate.
What happens on site during a dock leveller repair?
During a leveller repair the bay is closed, the leveller is isolated and propped, and the engineer works from the pit or deck to diagnose and repair the fault. Neighbouring bays normally keep working.
- Close the bay: no trailer on the dock, the door closed and forklifts kept away.
- Isolate and prop: the leveller is electrically isolated and locked off, and the platform raised and supported on its maintenance strut before anyone goes underneath.
- Clean and inspect: debris and spilt oil are cleared from the pit so the fault can be traced.
- Repair: parts are fitted or welded. Anything beyond the agreed scope is quoted first.
- Test: the leveller is cycled, the lip checked and controls tested before the bay reopens.
It helps if you can provide a clear bay, a contact on site, photos or labels showing the leveller type and size, and any insurer inspection report that lists the defect.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
Bay checks on a repair or service visit
- Manual override and emergency operation on powered doors
- Safety edges, photocells and light curtains
- Inflatable shelter fans, airbags and control function
- Track alignment, rollers and wall fixings
- Door panels, side seals and bottom rubbers
- Vehicle restraint engagement and its signal sequence
Options to discuss
Hydraulic repairs
Cylinders resealed or replaced, hoses and fittings renewed, check and safety valves tested, and the system refilled with fresh oil and bled so the platform moves smoothly again.
Structural and weld repairs
Cracked deck plates, broken welds and damaged front sections repaired by welding or with fabricated replacement parts, restoring the platform's strength.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Bordon. Planning and Building Regulations questions are never assumed either way: we check what applies before any work starts, so you know before work is booked.
Questions about dock leveller repairs in Bordon
Do you cover Hampshire for dock leveller repairs?
Yes. We take on dock leveller repairs for sites in Bordon and throughout Hampshire. Each visit is arranged in advance, with the price agreed in writing before anyone attends. Specialist service engineers working under our management carry out the work, and we remain your point of contact from the first call to the written report.
Can repairs be carried out outside our working hours?
Yes, by arrangement. Evening, night or weekend visits can be booked so that repairs and servicing at your Bordon site cause less disruption to loading. Out-of-hours attendance usually affects the price, so we include it when we agree the visit charge in writing. Tell us your shift pattern and the times when the dock is quietest.
Can you take over our existing loading bay maintenance arrangement?
Yes. Send us a list of the equipment at your Bordon site, with makes, models and approximate ages if known, plus recent service or inspection reports. We will propose a planned maintenance schedule and price it per item per visit. The first visit records the condition of everything, so you have a clear starting point for future servicing.
Will the repair clear an insurer's defect notice?
A repair addresses the defect listed, and our written report records what was found and what was done, which you can keep with the insurer's report. Whether the insurer needs to re-inspect is between you and them. Any further defects found during the repair are quoted before work.
Do you repair mechanical dock levellers?
Yes, where parts are still available. Mechanical levellers use springs and a hold-down mechanism rather than hydraulics, and common repairs include springs, release mechanisms and lip hinges. Where parts are hard to find or faults keep recurring, the report may suggest pricing a hydraulic replacement.
Dock leveller repairs near Bordon
Businesses outside Bordon may find their nearest town in this list: Alton (5 miles), Haslemere (7 miles) and Farnham (7 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Bordon
Full guide to dock leveller repairs · Everything we do in Bordon
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Bordon.