- Location
- Ferndown, Dorset
- Main postcode district
- BH22
- Nearby (straight line)
- Wimborne Minster (4 miles), Bournemouth (6 miles) and Christchurch (7 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Is this right for your site in Ferndown?
When a leveller at a warehouse near Ferndown sinks under load, it should be taken out of use until the hydraulic cause has been found and fixed. Low temperatures at chilled and frozen docks in Ferndown can affect hydraulic oil and seals, so it helps to mention the operating temperature when reporting a fault.
Distribution docks in Ferndown that run several shifts put heavy cycles through leveller hydraulics, so leaks and slow operation can show up sooner.
For dock leveller repairs at sites in Ferndown, you will always know the cost before anyone sets off. The visit is chargeable and its price is agreed in writing. Clear photos of the problem help the engineer arrive prepared. Where the visit reveals more work, we stop, explain and quote before going further, and a written report follows every attendance so you have a record of the condition of each item.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What else does the engineer check at the bay?
- Vehicle restraint engagement and its signal sequence
- Shelter curtains, frames and side pads for tears
- Wiring, isolators and motor performance under load
- Hydraulic oil level, hoses and cylinders for leaks
- Leveller toe guards and side skirting, where fitted
- Control panels, push buttons and emergency stops
Options to discuss
Control and safety repairs
Control panels, push buttons, limit switches, maintenance struts, toe guards and side skirts repaired or replaced so the leveller operates and parks safely.
Structural and weld repairs
Cracked deck plates, broken welds and damaged front sections repaired by welding or with fabricated replacement parts, restoring the platform's strength.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Ferndown. Planning and Building Regulations questions are never assumed either way: we check what applies before any work starts, so you know before work is booked.
Questions about dock leveller repairs in Ferndown
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
Do you provide a written report after each visit?
Yes. After every repair or service visit to a site in Ferndown, you receive a written report setting out what was checked, what was found, what work was carried out and anything that still needs attention, with a quote for further work where needed. The report is useful for your maintenance records and for discussions with your insurer or inspector.
Can you repair all makes of loading bay equipment?
We work on common makes and types of doors, dock levellers, shelters, seals and restraints. Parts availability varies, particularly for older or discontinued equipment, so it helps to send the make, model and photos of any data plates from your site in Ferndown. If original parts are not available, we tell you and price the alternatives, including replacement where that makes more sense.
Will the repair clear an insurer's defect notice?
A repair addresses the defect listed, and our written report records what was found and what was done, which you can keep with the insurer's report. Whether the insurer needs to re-inspect is between you and them. Any further defects found during the repair are quoted before work.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Dock leveller repairs near Ferndown
Looking beyond Ferndown? Our pages for Wimborne Minster (4 miles), Bournemouth (6 miles) and Christchurch (7 miles) describe the same loading bay services and how to get in touch.
Other loading bay services in Ferndown
Full guide to dock leveller repairs · Everything we do in Ferndown
Ready to talk about a loading bay in Ferndown? Call us, or send the details through the quote form.