- Location
- Bognor Regis, West Sussex
- Main postcode district
- PO21
- Nearby (straight line)
- Chichester (6 miles), Littlehampton (6 miles) and Emsworth (12 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
What matters for dock bumpers in Bognor Regis?
Distribution sheds in Bognor Regis that take trailers on and off the dock all day wear through bumper rubber faster than quieter sites, so it pays to check them at every service. When a landlord in Bognor Regis re-lets a unit, replacing tired bumpers is a modest cost that protects the leveller and dock wall for the incoming tenant.
Sites near Bognor Regis handling a mix of articulated trailers, rigid vehicles and vans may need taller bumpers or a second lower pair to protect the dock face.
It starts with a free site survey in Bognor Regis, where we measure the openings, check the dock and talk through how the bay is used. You then receive a fixed written quote. Once you accept, we manage the job: specialist installation engineers carry out the work under our management, planned around your deliveries, and out-of-hours working can be arranged. At handover we test everything with you and leave the documentation.
What happens on site when dock bumpers are fitted?
Fitting dock bumpers is a short job carried out from yard level, and only the bay being worked on is taken out of use.
- Isolate the bay: no trailer on the dock, the leveller parked and the door closed, with the yard area in front coned off.
- Remove the old bumpers: worn units and corroded fixings are taken off and the dock face is checked for cracked or spalled concrete.
- Fix the new bumpers: holes are drilled and the bumpers secured with resin or mechanical anchors, or welded to existing steelwork where that gives the better fixing.
- Allow cure time: resin anchors need time to cure before a trailer is reversed on to them, and the engineer will confirm when the bay can reopen.
We ask you to provide a clear bay, safe access to the yard, a named contact on the day and details of any permit-to-work or site induction. If the dock face needs concrete repair first, that is identified at survey and priced in the quote rather than discovered on the day.
Do dock bumpers need inspecting under PUWER?
Dock bumpers should be checked whenever the loading bay is serviced, because they protect equipment that the Provision and Use of Work Equipment Regulations 1998 (PUWER) apply to. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
PUWER requires work equipment, including dock levellers, loading bay doors and shelters, to be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. A bumper worn down to its backing lets trailers strike the leveller lip and front plate, which can crack welds, bend hinges and leave a leveller that is no longer safe to drive across.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Replacing a worn bumper usually costs far less than repairing the leveller it should have protected.
The health and safety regulator is HSE in Great Britain and HSENI in Northern Ireland. Including bumpers in planned maintenance checks shows the dock is being looked after.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Wall and steel structure for door, shelter and bumper fixings
- Wheel guide positions and yard markings for reversing vehicles
- Wind exposure at the dock, which affects door and shelter choice
- Drainage on recessed or sloping dock approaches
- Lighting inside trailers and at the dock face
- Traffic routes for vehicles and separation of pedestrians
Options to discuss
Laminated rubber bumpers
Layers of fabric-reinforced rubber clamped between steel angles. Economical and good at absorbing impact, they are the standard choice for many general-purpose loading docks.
Moulded rubber bumpers
Solid moulded rubber blocks in rectangular or curved profiles. Compact and tidy, they suit vans, rigid vehicles and docks with lighter or less frequent traffic.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Bognor Regis. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock bumpers in Bognor Regis
Can you work outside our normal operating hours in Bognor Regis?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Bognor Regis, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
What details do you need from us to quote for dock bumpers?
To get started, send the site address in Bognor Regis, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Are dock bumpers included in a complete bay package?
Yes. When we supply a complete loading bay, dock bumpers are specified alongside the leveller, door and shelter or seal so that projection, height and seal compression all work together. Bumpers can also be ordered with wheel guides and dock lights as part of a smaller safety upgrade on an existing bay.
Can dock bumpers be fitted with an edge-of-dock leveller?
Yes. With an edge-of-dock leveller, bumpers are usually fixed to the dock face either side of the unit, or to the leveller's own mounting frame where it is designed for that. Their projection has to suit the short lip so it still reaches on to the trailer bed, which we check at survey.
Dock bumpers near Bognor Regis
Close neighbours of Bognor Regis with their own pages here: Chichester (6 miles), Littlehampton (6 miles) and Emsworth (12 miles). Choose one to see coverage details for that town.
Other loading bay services in Bognor Regis
Full guide to dock bumpers · Everything we do in Bognor Regis
Request a quote for your loading bay in Bognor Regis, attaching photos of the dock, the equipment and any damage.