- Location
- Cannock, Staffordshire
- Main postcode district
- WS11
- Nearby (straight line)
- Great Wyrley (2 miles), Burntwood (4 miles) and Bloxwich (5 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
What matters for telescopic-lip dock levellers in Cannock?
Before recommending a lip extension for a dock in Cannock, we record the trailers that actually arrive, including tail lifts and rear overhangs. Parcel and courier hubs in Cannock with varied vehicle types can use the longer lip reach to serve more of their fleet from fewer bays.
Cold chain operators around Cannock loading refrigerated trailers right to the doors may find a telescopic lip makes the last pallets far easier to handle.
The survey is free, the quote is written and the price is fixed: that is how every installation in Cannock begins. We then manage the work from start to finish. Fitting is carried out by specialist installers under our management, phased so the operation keeps moving, and nights or weekends can be booked by arrangement. On the final day we test the equipment with you and hand over the operating and maintenance information.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How should staff use a telescopic-lip leveller safely?
Staff should only operate a telescopic-lip leveller once the trailer is secured and the dock door is open, and should always return the lip and platform to the stored position before the trailer leaves. Simple routines prevent most damage.
- Extend the lip only as far as needed and check it has the overlap on the bed that the manufacturer specifies.
- Keep feet and loads clear of the platform sides while it moves; that is what the toe guards are for.
- Never operate the leveller with a forklift or load standing on it.
- Use the automatic return function where fitted, so the lip withdraws and the platform stores at the end of loading.
- Report hydraulic leaks, unusual noises or a sticking lip straight away.
Training new dock staff on these steps, and displaying them beside the control panel, keeps practice consistent across shifts.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Temperature requirements for chilled, frozen or ambient goods
- Control positions, isolators and any existing interlocks
- Working hours, shift patterns and windows for out-of-hours work
- Bumper position and wear or damage on the dock face
- Scope to convert ground-level doors into docks or add lift tables
- How drivers are prevented from pulling away too early
Options to discuss
1,000 mm lip extension
A longer reach that clears folded tail lifts and deep bumper projections, so rigids and tail-lift trailers can be loaded at the same bay.
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
What do the rules in England mean for the work?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Cannock. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about telescopic-lip dock levellers in Cannock
Is VAT included in your guide prices for telescopic-lip dock levellers?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Staffordshire as everywhere else: for telescopic-lip dock levellers, it is £6,800 to £11,800 per leveller, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
How long does installation take at a site in Cannock?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Cannock site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Can a telescopic lip bridge a larger gap to the trailer?
Yes, that is one of its strengths. Where deep bumpers hold the trailer further from the dock edge, a telescopic lip can extend to bridge a gap that a fixed swing lip may not cover. We check bumper projection at survey so the lip length suits the dock.
What overlap should the lip have on the trailer bed?
The lip should rest on the trailer bed with the overlap the manufacturer specifies, so it cannot slip off as the trailer moves under load. Extending further than needed adds no benefit. We show dock staff what a correct overlap looks like at handover.
Telescopic-lip dock levellers near Cannock
Looking beyond Cannock? Our pages for Great Wyrley (2 miles), Burntwood (4 miles) and Bloxwich (5 miles) describe the same loading bay services and how to get in touch.
Other loading bay services in Cannock
Full guide to telescopic-lip dock levellers · Everything we do in Cannock
If a loading bay in Cannock needs attention, call us or send photos and details online.