- Location
- Mexborough, South Yorkshire
- Main postcode district
- S64
- Nearby (straight line)
- Wath-upon-Dearne (2 miles), Conisbrough (3 miles) and Rawmarsh (3 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
Why do sites in Mexborough choose this?
Before recommending a lip extension for a dock in Mexborough, we record the trailers that actually arrive, including tail lifts and rear overhangs. Retail distribution sites in Mexborough receiving both artics and tail-lift rigids at the same bays can handle the whole mix with a telescopic-lip leveller.
Manufacturing sites in Mexborough that end-load finished goods can place the lip precisely between pallets to reach the rear row.
Here is what happens after you contact us about a site in Mexborough. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How far should a telescopic lip extend?
A telescopic lip should extend far enough to reach clear bed space on every trailer you load, including over tail lifts, while still leaving a secure overlap on the bed. Telescopic lips commonly extend 500 to 1,000 mm.
- Around 500 mm: suits fleets without tail lifts that need precise placement and end loading.
- Up to around 1,000 mm: reaches over folded tail lifts and across the larger gap left where deep bumpers hold trailers back from the dock edge.
- Platform length: should match the lip, as a long reach on a short platform can leave steep gradients.
- Lip width: full-width lips suit most work, while narrower or tapered lips help with smaller vehicles.
We record the rear details of the trailers you receive, including tail lift depth and bumper projection, then recommend the shortest extension that covers them all. A longer lip than you need adds cost and weight without benefit.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Temperature requirements for chilled, frozen or ambient goods
- Working hours, shift patterns and windows for out-of-hours work
- Forklift and pallet truck loads crossing the leveller platform
- How drivers are prevented from pulling away too early
- Bumper position and wear or damage on the dock face
- Whether planning, building control or a building warrant may be needed
Options to discuss
500 mm lip extension
A commonly specified reach for precise placement and end loading on standard trailers and refrigerated vehicles that do not have tail lifts.
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
Which rules apply in England?
Lift tables and dock lifts in Mexborough may fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted. It depends on the equipment and how it is used, and your insurer or competent person will confirm. Dock levellers are usually treated as work equipment under PUWER. We check what applies at survey.
Questions about telescopic-lip dock levellers in Mexborough
Do you cover Mexborough for telescopic-lip dock levellers?
Yes. We take on telescopic-lip dock levellers for businesses in Mexborough and across South Yorkshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Is VAT included in your guide prices for telescopic-lip dock levellers?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in South Yorkshire as everywhere else: for telescopic-lip dock levellers, it is £6,800 to £11,800 per leveller, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
What details do you need from us to quote for telescopic-lip dock levellers?
To get started, send the site address in Mexborough, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Is a telescopic lip slower to operate?
Slightly, because the lip is extended as a separate movement rather than swinging out as the platform rises. In practice the difference is small, and automatic sequences can raise the platform and extend the lip in one action, then return both at the end of loading.
What overlap should the lip have on the trailer bed?
The lip should rest on the trailer bed with the overlap the manufacturer specifies, so it cannot slip off as the trailer moves under load. Extending further than needed adds no benefit. We show dock staff what a correct overlap looks like at handover.
Telescopic-lip dock levellers near Mexborough
Sites close to Mexborough get the same service, including those in Wath-upon-Dearne (2 miles), Conisbrough (3 miles) and Rawmarsh (3 miles), with every job run the same way.
Other loading bay services in Mexborough
Full guide to telescopic-lip dock levellers · Everything we do in Mexborough
Request a quote for your loading bay in Mexborough, attaching photos of the dock, the equipment and any damage.