- Location
- Portishead, Somerset
- Main postcode district
- BS20
- Nearby (straight line)
- Avonmouth (3 miles), Nailsea (3 miles) and Clevedon (5 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
Why do sites in Portishead choose this?
Parcel and courier hubs in Portishead with varied vehicle types can use the longer lip reach to serve more of their fleet from fewer bays. Before recommending a lip extension for a dock in Portishead, we record the trailers that actually arrive, including tail lifts and rear overhangs.
Manufacturing sites in Portishead that end-load finished goods can place the lip precisely between pallets to reach the rear row.
If you are planning telescopic-lip dock levellers for a site in Portishead, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
How are drive-away risks managed while the lip rests on a trailer?
Drive-away risks are managed by stopping the vehicle leaving until loading has finished and the lip has been withdrawn, using traffic lights, vehicle or trailer restraints, or the person in charge keeping the keys or paperwork. HSE workplace transport guidance (HSG136) and the HSE loading factsheet (followed by HSENI in Northern Ireland) call for safeguards against drivers driving away too early.
- Why it matters: a lip resting on the bed is only safe while the trailer stays put, and trailer creep during forklift loading can open a gap at the dock edge.
- Equipment duties: the leveller is work equipment under PUWER 1998 in Great Britain or PUWER (Northern Ireland) 1999, so it must be maintained and inspected where deterioration could lead to danger. Engineering insurers commonly inspect at 12-month intervals.
- Standard: BS EN 1398:2009 sets the safety requirements for dock levellers and is current, under review.
Enforcement is by HSE in Great Britain and HSENI in Northern Ireland. Our guide to preventing drive-away and trailer creep compares the safeguards.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Condition of any existing leveller pit, kerb angles and pit drainage
- Lighting inside trailers and at the dock face
- Scope to convert ground-level doors into docks or add lift tables
- How often each door cycles during a typical shift
- Control positions, isolators and any existing interlocks
- Wind exposure at the dock, which affects door and shelter choice
Options to discuss
1,000 mm lip extension
A longer reach that clears folded tail lifts and deep bumper projections, so rigids and tail-lift trailers can be loaded at the same bay.
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Portishead, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about telescopic-lip dock levellers in Portishead
Will you deal with building control and planning for a project in Portishead?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Portishead, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Is the site survey in Portishead free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Can a telescopic lip bridge a larger gap to the trailer?
Yes, that is one of its strengths. Where deep bumpers hold the trailer further from the dock edge, a telescopic lip can extend to bridge a gap that a fixed swing lip may not cover. We check bumper projection at survey so the lip length suits the dock.
Can telescopic and swing-lip levellers be mixed on one dock?
Yes, and many sites do. Fitting telescopic levellers on the bays that receive tail-lift vehicles or need end loading, and swing-lip units on the rest, keeps costs down while covering every vehicle type. Clear bay signage helps drivers reverse onto the right one.
Telescopic-lip dock levellers near Portishead
Looking beyond Portishead? Our pages for Avonmouth (3 miles), Nailsea (3 miles) and Clevedon (5 miles) describe the same loading bay services and how to get in touch.
Other loading bay services in Portishead
Full guide to telescopic-lip dock levellers · Everything we do in Portishead
Phone us to discuss your loading bay in Portishead, or start with the online quote tool if you prefer to send details first.