- Location
- Telford, Shropshire
- Main postcode district
- TF3
- Nearby (straight line)
- Wellington (3 miles), Shrewsbury (13 miles) and Wolverhampton (15 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
What matters for telescopic-lip dock levellers in Telford?
Cold chain operators around Telford loading refrigerated trailers right to the doors may find a telescopic lip makes the last pallets far easier to handle. Retail distribution sites in Telford receiving both artics and tail-lift rigids at the same bays can handle the whole mix with a telescopic-lip leveller.
Replacing worn swing-lip levellers at a site in Telford is a good moment to ask whether the current trailer mix now calls for telescopic lips.
A single contact at Loading Bay Doors handles your project in Telford from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How should staff use a telescopic-lip leveller safely?
Staff should only operate a telescopic-lip leveller once the trailer is secured and the dock door is open, and should always return the lip and platform to the stored position before the trailer leaves. Simple routines prevent most damage.
- Extend the lip only as far as needed and check it has the overlap on the bed that the manufacturer specifies.
- Keep feet and loads clear of the platform sides while it moves; that is what the toe guards are for.
- Never operate the leveller with a forklift or load standing on it.
- Use the automatic return function where fitted, so the lip withdraws and the platform stores at the end of loading.
- Report hydraulic leaks, unusual noises or a sticking lip straight away.
Training new dock staff on these steps, and displaying them beside the control panel, keeps practice consistent across shifts.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Drainage on recessed or sloping dock approaches
- Yard gradient and the slope of the approach to the dock
- Condition of any existing leveller pit, kerb angles and pit drainage
- Dock height and the mix of trailers you load
- How often each door cycles during a typical shift
- Age and condition of the equipment already in place
Options to discuss
500 mm lip extension
A commonly specified reach for precise placement and end loading on standard trailers and refrigerated vehicles that do not have tail lifts.
1,000 mm lip extension
A longer reach that clears folded tail lifts and deep bumper projections, so rigids and tail-lift trailers can be loaded at the same bay.
Regulations and approvals in England
Sites in Telford fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about telescopic-lip dock levellers in Telford
What details do you need from us to quote for telescopic-lip dock levellers?
To get started, send the site address in Telford, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Do you cover Telford for telescopic-lip dock levellers?
Yes. We take on telescopic-lip dock levellers for businesses in Telford and across Shropshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Which building and safety rules apply to a site in Telford?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Telford, we check what applies at survey and design to it.
Do telescopic levellers need more maintenance?
They have more moving parts than a swing-lip leveller, including the lip guides and lip cylinder, so these need checking and lubricating at each service. With planned servicing the extra work is modest. Servicing is chargeable, with the visit price agreed in advance.
Can telescopic and swing-lip levellers be mixed on one dock?
Yes, and many sites do. Fitting telescopic levellers on the bays that receive tail-lift vehicles or need end loading, and swing-lip units on the rest, keeps costs down while covering every vehicle type. Clear bay signage helps drivers reverse onto the right one.
Telescopic-lip dock levellers near Telford
Other towns within reach of Telford on our coverage list include Wellington (3 miles), Shrewsbury (13 miles) and Wolverhampton (15 miles), all covered on the same terms.
Other loading bay services in Telford
Full guide to telescopic-lip dock levellers · Everything we do in Telford
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Telford.