- Location
- Perth, Perth and Kinross
- Main postcode district
- PH1
- Nearby (straight line)
- Blairgowrie (14 miles), Crieff (16 miles) and Glenrothes (17 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
What should sites in Perth consider?
Manufacturing sites in Perth that end-load finished goods can place the lip precisely between pallets to reach the rear row. Replacing worn swing-lip levellers at a site in Perth is a good moment to ask whether the current trailer mix now calls for telescopic lips.
Retail distribution sites in Perth receiving both artics and tail-lift rigids at the same bays can handle the whole mix with a telescopic-lip leveller.
If you are planning telescopic-lip dock levellers for a site in Perth, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
Which operations benefit most from a telescopic lip?
Telescopic lips benefit operations that need precise lip placement, load trailers right to the rear doors, or receive vehicles with tail lifts. A swing lip lands wherever its fixed length takes it, while a telescopic lip can be stopped exactly where it is wanted.
- End loading: the lip can be placed in the gap between pallets so the last row can be loaded or removed.
- Tail-lift trailers and rigids: the lip reaches over the folded tail lift onto the bed.
- Cold chain: pallets are often loaded tight to the rear doors of refrigerated trailers.
- Double-deck and container trailers: beds sit at varied heights and lip placement needs care.
- Mixed fleets: one bay can handle a wider range of vehicles.
For straightforward pallet loading of standard trailers, a swing-lip dock leveller is simpler and lower in cost.
How are drive-away risks managed while the lip rests on a trailer?
Drive-away risks are managed by stopping the vehicle leaving until loading has finished and the lip has been withdrawn, using traffic lights, vehicle or trailer restraints, or the person in charge keeping the keys or paperwork. HSE workplace transport guidance (HSG136) and the HSE loading factsheet (followed by HSENI in Northern Ireland) call for safeguards against drivers driving away too early.
- Why it matters: a lip resting on the bed is only safe while the trailer stays put, and trailer creep during forklift loading can open a gap at the dock edge.
- Equipment duties: the leveller is work equipment under PUWER 1998 in Great Britain or PUWER (Northern Ireland) 1999, so it must be maintained and inspected where deterioration could lead to danger. Engineering insurers commonly inspect at 12-month intervals.
- Standard: BS EN 1398:2009 sets the safety requirements for dock levellers and is current, under review.
Enforcement is by HSE in Great Britain and HSENI in Northern Ireland. Our guide to preventing drive-away and trailer creep compares the safeguards.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- How drivers are prevented from pulling away too early
- Temperature requirements for chilled, frozen or ambient goods
- Lighting inside trailers and at the dock face
- Forklift and pallet truck loads crossing the leveller platform
- Wall and steel structure for door, shelter and bumper fixings
- Scope to convert ground-level doors into docks or add lift tables
Options to discuss
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
1,000 mm lip extension
A longer reach that clears folded tail lifts and deep bumper projections, so rigids and tail-lift trailers can be loaded at the same bay.
Planning, building control and safety law in Scotland
Energy standards for buildings in Scotland are set out in Section 6 of the Building Standards Technical Handbook. For new or replacement loading bay doors in Perth, we confirm the figure that applies to your project and check what applies at survey, rather than relying on rules written for elsewhere in the UK.
Questions about telescopic-lip dock levellers in Perth
Is VAT included in your guide prices for telescopic-lip dock levellers?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Perth and Kinross as everywhere else: for telescopic-lip dock levellers, it is £6,800 to £11,800 per leveller, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Perth, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Can you work alongside our main contractor on a new build in Perth?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Do telescopic levellers need more maintenance?
They have more moving parts than a swing-lip leveller, including the lip guides and lip cylinder, so these need checking and lubricating at each service. With planned servicing the extra work is modest. Servicing is chargeable, with the visit price agreed in advance.
Is a telescopic lip slower to operate?
Slightly, because the lip is extended as a separate movement rather than swinging out as the platform rises. In practice the difference is small, and automatic sequences can raise the platform and extend the lip in one action, then return both at the end of loading.
Telescopic-lip dock levellers near Perth
Distances are measured from Perth. Nearby towns we cover include Blairgowrie (14 miles), Crieff (16 miles) and Glenrothes (17 miles), and other towns in the area are covered too.
Other loading bay services in Perth
Full guide to telescopic-lip dock levellers · Everything we do in Perth
Tell us what is happening at your Perth dock, what equipment is there and when it is used, and we will suggest the right next step.