- Location
- Spalding, Lincolnshire
- Main postcode district
- PE11
- Nearby (straight line)
- Boston (14 miles), Peterborough (15 miles) and Wisbech (15 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
Why do sites in Spalding choose this?
A container-handling operation in Spalding can benefit from a telescopic lip, as container floors and chassis heights vary more than standard trailers. Replacing worn swing-lip levellers at a site in Spalding is a good moment to ask whether the current trailer mix now calls for telescopic lips.
Cold chain operators around Spalding loading refrigerated trailers right to the doors may find a telescopic lip makes the last pallets far easier to handle.
Keeping the dock running is usually the first concern, so we plan around it. After a free survey of your Spalding site and a written quote at a fixed price, we agree when each bay can be released and whether any work should happen out of hours. Specialist installation engineers working under our management then fit the equipment, and we test it and hand over the documentation before the bay goes back into use.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How should staff use a telescopic-lip leveller safely?
Staff should only operate a telescopic-lip leveller once the trailer is secured and the dock door is open, and should always return the lip and platform to the stored position before the trailer leaves. Simple routines prevent most damage.
- Extend the lip only as far as needed and check it has the overlap on the bed that the manufacturer specifies.
- Keep feet and loads clear of the platform sides while it moves; that is what the toe guards are for.
- Never operate the leveller with a forklift or load standing on it.
- Use the automatic return function where fitted, so the lip withdraws and the platform stores at the end of loading.
- Report hydraulic leaks, unusual noises or a sticking lip straight away.
Training new dock staff on these steps, and displaying them beside the control panel, keeps practice consistent across shifts.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Working hours, shift patterns and windows for out-of-hours work
- Condition of any existing leveller pit, kerb angles and pit drainage
- How often each door cycles during a typical shift
- Traffic routes for vehicles and separation of pedestrians
- Asbestos register and any other site hazard information
- Escape routes and pedestrian doors close to the bay
Options to discuss
Automatic return control
A single button that withdraws the lip and lowers the platform to its stored position, reducing the risk of a trailer leaving with the lip still out.
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
Regulations and approvals in England
Sites in Spalding fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about telescopic-lip dock levellers in Spalding
How do you price telescopic-lip dock levellers for a site in Spalding?
Guide budgets for supply and fit are £6,800 to £11,800 per leveller, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
What details do you need from us to quote for telescopic-lip dock levellers?
To get started, send the site address in Spalding, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can you work outside our normal operating hours in Spalding?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
What overlap should the lip have on the trailer bed?
The lip should rest on the trailer bed with the overlap the manufacturer specifies, so it cannot slip off as the trailer moves under load. Extending further than needed adds no benefit. We show dock staff what a correct overlap looks like at handover.
Do telescopic levellers need more maintenance?
They have more moving parts than a swing-lip leveller, including the lip guides and lip cylinder, so these need checking and lubricating at each service. With planned servicing the extra work is modest. Servicing is chargeable, with the visit price agreed in advance.
Telescopic-lip dock levellers near Spalding
Close neighbours of Spalding with their own pages here: Boston (14 miles), Peterborough (15 miles) and Wisbech (15 miles). Choose one to see coverage details for that town.
Other loading bay services in Spalding
Full guide to telescopic-lip dock levellers · Everything we do in Spalding
Tell us what is happening at your Spalding dock, what equipment is there and when it is used, and we will suggest the right next step.