- Location
- Aldershot, Hampshire
- Main postcode district
- GU12
- Nearby (straight line)
- Farnham (3 miles), Farnborough (3 miles) and Fleet (4 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
What should sites in Aldershot consider?
Parcel and courier hubs in Aldershot with varied vehicle types can use the longer lip reach to serve more of their fleet from fewer bays. Replacing worn swing-lip levellers at a site in Aldershot is a good moment to ask whether the current trailer mix now calls for telescopic lips.
Manufacturing sites in Aldershot that end-load finished goods can place the lip precisely between pallets to reach the rear row.
If you are planning telescopic-lip dock levellers for a site in Aldershot, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How should staff use a telescopic-lip leveller safely?
Staff should only operate a telescopic-lip leveller once the trailer is secured and the dock door is open, and should always return the lip and platform to the stored position before the trailer leaves. Simple routines prevent most damage.
- Extend the lip only as far as needed and check it has the overlap on the bed that the manufacturer specifies.
- Keep feet and loads clear of the platform sides while it moves; that is what the toe guards are for.
- Never operate the leveller with a forklift or load standing on it.
- Use the automatic return function where fitted, so the lip withdraws and the platform stores at the end of loading.
- Report hydraulic leaks, unusual noises or a sticking lip straight away.
Training new dock staff on these steps, and displaying them beside the control panel, keeps practice consistent across shifts.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Power supply at each bay, including three-phase availability
- Headroom above the opening and which track type will suit it
- Temperature requirements for chilled, frozen or ambient goods
- Wind exposure at the dock, which affects door and shelter choice
- Age and condition of the equipment already in place
- Control positions, isolators and any existing interlocks
Options to discuss
1,000 mm lip extension
A longer reach that clears folded tail lifts and deep bumper projections, so rigids and tail-lift trailers can be loaded at the same bay.
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
Regulations and approvals in England
Sites in Aldershot fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about telescopic-lip dock levellers in Aldershot
Will you deal with building control and planning for a project in Aldershot?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Aldershot site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Can you work alongside our main contractor on a new build in Aldershot?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Is a telescopic lip slower to operate?
Slightly, because the lip is extended as a separate movement rather than swinging out as the platform rises. In practice the difference is small, and automatic sequences can raise the platform and extend the lip in one action, then return both at the end of loading.
Can a telescopic lip bridge a larger gap to the trailer?
Yes, that is one of its strengths. Where deep bumpers hold the trailer further from the dock edge, a telescopic lip can extend to bridge a gap that a fixed swing lip may not cover. We check bumper projection at survey so the lip length suits the dock.
Telescopic-lip dock levellers near Aldershot
If your site is not in Aldershot itself, it may be near one of these: Farnham (3 miles), Farnborough (3 miles) and Fleet (4 miles). Pick the closest.
Other loading bay services in Aldershot
Full guide to telescopic-lip dock levellers · Everything we do in Aldershot
Use the quote tool to tell us about the doors, levellers or shelters at your Aldershot site, and we will be in touch to arrange the next step.