- Location
- Exeter, Devon
- Main postcode district
- EX2
- Nearby (straight line)
- Exmouth (9 miles), Tiverton (12 miles) and Newton Abbot (14 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
Why do sites in Exeter choose this?
Retail distribution sites in Exeter receiving both artics and tail-lift rigids at the same bays can handle the whole mix with a telescopic-lip leveller. Before recommending a lip extension for a dock in Exeter, we record the trailers that actually arrive, including tail lifts and rear overhangs.
Parcel and courier hubs in Exeter with varied vehicle types can use the longer lip reach to serve more of their fleet from fewer bays.
We do not give a fixed price without seeing the site. A free survey in Exeter lets us check the details that affect the job, and the written quote that follows is a fixed price for the agreed scope. We plan the work around your operation, arrange out-of-hours access if you need it and manage specialist installation engineers throughout. Handover includes testing, a demonstration and the paperwork you need for your records.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How far should a telescopic lip extend?
A telescopic lip should extend far enough to reach clear bed space on every trailer you load, including over tail lifts, while still leaving a secure overlap on the bed. Telescopic lips commonly extend 500 to 1,000 mm.
- Around 500 mm: suits fleets without tail lifts that need precise placement and end loading.
- Up to around 1,000 mm: reaches over folded tail lifts and across the larger gap left where deep bumpers hold trailers back from the dock edge.
- Platform length: should match the lip, as a long reach on a short platform can leave steep gradients.
- Lip width: full-width lips suit most work, while narrower or tapered lips help with smaller vehicles.
We record the rear details of the trailers you receive, including tail lift depth and bumper projection, then recommend the shortest extension that covers them all. A longer lip than you need adds cost and weight without benefit.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Lighting inside trailers and at the dock face
- Wheel guide positions and yard markings for reversing vehicles
- Asbestos register and any other site hazard information
- Power supply at each bay, including three-phase availability
- Bumper position and wear or damage on the dock face
- Working hours, shift patterns and windows for out-of-hours work
Options to discuss
Automatic return control
A single button that withdraws the lip and lowers the platform to its stored position, reducing the risk of a trailer leaving with the lip still out.
500 mm lip extension
A commonly specified reach for precise placement and end loading on standard trailers and refrigerated vehicles that do not have tail lifts.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Exeter. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about telescopic-lip dock levellers in Exeter
How long does installation take at a site in Exeter?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Will you deal with building control and planning for a project in Exeter?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Exeter site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Are telescopic levellers suitable for cold stores?
Yes, telescopic levellers are widely used in cold stores because refrigerated trailers are often loaded right to the rear doors. Insulated platforms and perimeter seals reduce cold loss through the pit, and the leveller is usually interlocked with the door and shelter.
What overlap should the lip have on the trailer bed?
The lip should rest on the trailer bed with the overlap the manufacturer specifies, so it cannot slip off as the trailer moves under load. Extending further than needed adds no benefit. We show dock staff what a correct overlap looks like at handover.
Telescopic-lip dock levellers near Exeter
The same survey, quote and repair service is available in towns around Exeter, such as Exmouth (9 miles), Tiverton (12 miles) and Newton Abbot (14 miles).
Other loading bay services in Exeter
Full guide to telescopic-lip dock levellers · Everything we do in Exeter
Start your enquiry for Exeter through the quote tool. A few photos and approximate sizes help us respond with something useful.