- Location
- Dunstable, Bedfordshire
- Main postcode district
- LU6
- Nearby (straight line)
- Luton (5 miles), Leighton Buzzard (6 miles) and Harpenden (9 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
Is this right for your site in Dunstable?
Parcel and courier hubs in Dunstable with varied vehicle types can use the longer lip reach to serve more of their fleet from fewer bays. Retail distribution sites in Dunstable receiving both artics and tail-lift rigids at the same bays can handle the whole mix with a telescopic-lip leveller.
Manufacturing sites in Dunstable that end-load finished goods can place the lip precisely between pallets to reach the rear row.
How does an installation in Dunstable work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
Which operations benefit most from a telescopic lip?
Telescopic lips benefit operations that need precise lip placement, load trailers right to the rear doors, or receive vehicles with tail lifts. A swing lip lands wherever its fixed length takes it, while a telescopic lip can be stopped exactly where it is wanted.
- End loading: the lip can be placed in the gap between pallets so the last row can be loaded or removed.
- Tail-lift trailers and rigids: the lip reaches over the folded tail lift onto the bed.
- Cold chain: pallets are often loaded tight to the rear doors of refrigerated trailers.
- Double-deck and container trailers: beds sit at varied heights and lip placement needs care.
- Mixed fleets: one bay can handle a wider range of vehicles.
For straightforward pallet loading of standard trailers, a swing-lip dock leveller is simpler and lower in cost.
How are drive-away risks managed while the lip rests on a trailer?
Drive-away risks are managed by stopping the vehicle leaving until loading has finished and the lip has been withdrawn, using traffic lights, vehicle or trailer restraints, or the person in charge keeping the keys or paperwork. HSE workplace transport guidance (HSG136) and the HSE loading factsheet (followed by HSENI in Northern Ireland) call for safeguards against drivers driving away too early.
- Why it matters: a lip resting on the bed is only safe while the trailer stays put, and trailer creep during forklift loading can open a gap at the dock edge.
- Equipment duties: the leveller is work equipment under PUWER 1998 in Great Britain or PUWER (Northern Ireland) 1999, so it must be maintained and inspected where deterioration could lead to danger. Engineering insurers commonly inspect at 12-month intervals.
- Standard: BS EN 1398:2009 sets the safety requirements for dock levellers and is current, under review.
Enforcement is by HSE in Great Britain and HSENI in Northern Ireland. Our guide to preventing drive-away and trailer creep compares the safeguards.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Whether planning, building control or a building warrant may be needed
- How often each door cycles during a typical shift
- Scope to convert ground-level doors into docks or add lift tables
- Control positions, isolators and any existing interlocks
- Escape routes and pedestrian doors close to the bay
- Gaps around trailers where heated or chilled air escapes
Options to discuss
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
500 mm lip extension
A commonly specified reach for precise placement and end loading on standard trailers and refrigerated vehicles that do not have tail lifts.
Regulations and approvals in England
Lift tables and dock lifts in Dunstable may fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted. It depends on the equipment and how it is used, and your insurer or competent person will confirm. Dock levellers are usually treated as work equipment under PUWER. We check what applies at survey.
Questions about telescopic-lip dock levellers in Dunstable
Will you deal with building control and planning for a project in Dunstable?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
How long does installation take at a site in Dunstable?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Is VAT included in your guide prices for telescopic-lip dock levellers?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Bedfordshire as everywhere else: for telescopic-lip dock levellers, it is £6,800 to £11,800 per leveller, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Is a telescopic lip slower to operate?
Slightly, because the lip is extended as a separate movement rather than swinging out as the platform rises. In practice the difference is small, and automatic sequences can raise the platform and extend the lip in one action, then return both at the end of loading.
Do telescopic levellers need more maintenance?
They have more moving parts than a swing-lip leveller, including the lip guides and lip cylinder, so these need checking and lubricating at each service. With planned servicing the extra work is modest. Servicing is chargeable, with the visit price agreed in advance.
Telescopic-lip dock levellers near Dunstable
Close neighbours of Dunstable with their own pages here: Luton (5 miles), Leighton Buzzard (6 miles) and Harpenden (9 miles). Choose one to see coverage details for that town.
Other loading bay services in Dunstable
Full guide to telescopic-lip dock levellers · Everything we do in Dunstable
For a written price on loading bay work in Dunstable, request a quote and include photos of the bay if you can.