A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
Why do sites in Argyll and Bute choose this?
Manufacturing sites in Argyll and Bute that end-load finished goods can place the lip precisely between pallets to reach the rear row. A container-handling operation in Argyll and Bute can benefit from a telescopic lip, as container floors and chassis heights vary more than standard trailers.
Retail distribution sites in Argyll and Bute receiving both artics and tail-lift rigids at the same bays can handle the whole mix with a telescopic-lip leveller.
How does an installation in Argyll and Bute work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How far should a telescopic lip extend?
A telescopic lip should extend far enough to reach clear bed space on every trailer you load, including over tail lifts, while still leaving a secure overlap on the bed. Telescopic lips commonly extend 500 to 1,000 mm.
- Around 500 mm: suits fleets without tail lifts that need precise placement and end loading.
- Up to around 1,000 mm: reaches over folded tail lifts and across the larger gap left where deep bumpers hold trailers back from the dock edge.
- Platform length: should match the lip, as a long reach on a short platform can leave steep gradients.
- Lip width: full-width lips suit most work, while narrower or tapered lips help with smaller vehicles.
We record the rear details of the trailers you receive, including tail lift depth and bumper projection, then recommend the shortest extension that covers them all. A longer lip than you need adds cost and weight without benefit.
Towns we cover in Argyll and Bute
We take enquiries about telescopic-lip dock levellers from across Argyll and Bute. These are the towns with their own pages:
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Regulations and approvals in Scotland
Lift tables at Scottish sites are lifting equipment under LOLER, which means thorough examination at least every 12 months, or every 6 months if people are lifted, depending on the equipment and its use. For a site in Argyll and Bute, your insurer or competent person will confirm the interval, and we check what applies at survey.
Questions
Which building and safety rules apply to a site in Argyll and Bute?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Argyll and Bute, we check what applies at survey and design to it.
Can you work outside our normal operating hours in Argyll and Bute?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Can a telescopic lip bridge a larger gap to the trailer?
Yes, that is one of its strengths. Where deep bumpers hold the trailer further from the dock edge, a telescopic lip can extend to bridge a gap that a fixed swing lip may not cover. We check bumper projection at survey so the lip length suits the dock.
Do telescopic levellers need more maintenance?
They have more moving parts than a swing-lip leveller, including the lip guides and lip cylinder, so these need checking and lubricating at each service. With planned servicing the extra work is modest. Servicing is chargeable, with the visit price agreed in advance.
Other services in Argyll and Bute
Full guide to telescopic-lip dock levellers · All loading bay services in Argyll and Bute