- Location
- Bedworth, Warwickshire
- Main postcode district
- CV12
- Nearby (straight line)
- Nuneaton (3 miles), Coventry (5 miles) and Hinckley (6 miles)
- Survey and quote
- Free, with a fixed written quote
A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
Why do sites in Bedworth choose this?
Warehouses across Bedworth that still rely on single-skin shutters may switch to insulated sectional doors when heating costs or cold goods-in areas become a problem. Ageing units around Bedworth sometimes have low lintels or pipework above the opening, which a low-headroom or high-lift track can be chosen to work around.
If you are fitting out a new warehouse in Bedworth, specifying insulated sectional doors from the start avoids disruptive changes once the building is occupied.
Step one is a survey at your site in Bedworth, which costs nothing and carries no obligation. Step two is a written quote with a fixed price and a clear scope. Step three is installation, scheduled around your operation and carried out by specialist installation engineers working under our management, including evenings or weekends if agreed. Step four is handover, when the equipment is tested in front of you and the paperwork is passed over.
Do sectional loading bay doors have to meet energy and safety rules?
Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
- Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
- Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.
How much does a sectional loading bay door cost?
A sectional loading bay door typically costs £2,400 to £5,200 per door, excluding VAT, supply and fit, for a made-to-measure insulated door fitted and working.
Where your door lands in the range depends on:
- Opening size: larger doors need more panel area, heavier springs and longer track.
- Panel thickness and finish: thicker insulated panels and non-standard colours add cost.
- Track type: high-lift and vertical lift tracks use more steel and fixings than standard lift.
- Operation: an electric operator with safety edge and photocells costs more than chain or push-up operation.
- Vision panels and extras: glazed sections, interlocks to the leveller and links to traffic lights.
- Site conditions: removing an old door, making good the opening, getting power to the door head and out-of-hours working.
We price after a free site survey, and the written quote is the fixed price for the work described. You can compare typical figures on our price guide.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Age and condition of the equipment already in place
- Lighting inside trailers and at the dock face
- Control positions, isolators and any existing interlocks
- Temperature requirements for chilled, frozen or ambient goods
- Clear opening width and height for each door
- Escape routes and pedestrian doors close to the bay
Options to discuss
High-lift or vertical lift track
Track arrangements that keep the open door clear of lights, sprinkler pipes, racking and forklift masts in buildings with plenty of height above the opening.
Electric operator
A shaft-mounted or trolley operator with push-button controls, safety edge and photocells. Suits busy bays and can be interlocked with levellers, shelters and traffic lights.
Which rules apply in England?
Workplace safety in England is regulated by HSE. For a loading bay in Bedworth, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about sectional loading bay doors in Bedworth
Do you cover Bedworth for sectional loading bay doors?
Yes. We take on sectional loading bay doors for businesses in Bedworth and across Warwickshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Bedworth site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Which building and safety rules apply to a site in Bedworth?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Bedworth, we check what applies at survey and design to it.
Can a sectional dock door be made to fit our existing opening?
Yes, sectional doors are made to measure, so they can be fitted to most existing dock openings. We measure the structural opening, headroom and side room at survey and choose a track to suit. Uneven reveals or a low lintel can usually be dealt with using packers, steel angles or a low-headroom track rather than building work.
What panel thickness should we choose for a heated warehouse?
For most heated warehouses a panel at the thicker end of the common 40 to 80 mm range is the sensible starting point, because it insulates better. Thinner panels can suit unheated stores. New and replacement doors also need to meet the energy rules for your nation, which we check when specifying.
Sectional loading bay doors near Bedworth
Sites close to Bedworth get the same service, including those in Nuneaton (3 miles), Coventry (5 miles) and Hinckley (6 miles), with every job run the same way.
Other loading bay services in Bedworth
Full guide to sectional loading bay doors · Everything we do in Bedworth
Request a quote for your loading bay in Bedworth, attaching photos of the dock, the equipment and any damage.