- Location
- Burnley, Lancashire
- Main postcode district
- BB11
- Nearby (straight line)
- Nelson (3 miles), Colne (5 miles) and Accrington (6 miles)
- Survey and quote
- Free, with a fixed written quote
A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
Is this right for your site in Burnley?
Food and drink businesses in Burnley running temperature-controlled goods-in areas can choose thicker panels to hold conditions steady between deliveries. Warehouses across Burnley that still rely on single-skin shutters may switch to insulated sectional doors when heating costs or cold goods-in areas become a problem.
If you are fitting out a new warehouse in Burnley, specifying insulated sectional doors from the start avoids disruptive changes once the building is occupied.
Keeping the dock running is usually the first concern, so we plan around it. After a free survey of your Burnley site and a written quote at a fixed price, we agree when each bay can be released and whether any work should happen out of hours. Specialist installation engineers working under our management then fit the equipment, and we test it and hand over the documentation before the bay goes back into use.
Do sectional loading bay doors have to meet energy and safety rules?
Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
- Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
- Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.
What happens on site when a sectional dock door is installed?
Fitting a sectional dock door often takes around a day per opening once the door is on site, though very large doors or awkward fixings take longer. The bay is out of use while the work is under way.
A typical installation runs like this:
- The old door, if there is one, is taken down and removed from site.
- Steel angles or packers are fixed to the opening so the tracks run true.
- Tracks, springs and panels are assembled and the door is balanced.
- The operator, safety edge, photocells and controls are fitted and wired.
- The door is tested, adjusted and handed over.
Before we arrive you will need a clear area inside the opening for access equipment and the bay taken out of service. Electric doors also need a suitable isolated power supply near the door head, single or three-phase depending on the operator, which we confirm in the quote. On multi-door sites we work bay by bay so the rest of the dock keeps running.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Power supply at each bay, including three-phase availability
- How drivers are prevented from pulling away too early
- Forklift and pallet truck loads crossing the leveller platform
- Scope to convert ground-level doors into docks or add lift tables
- Wheel guide positions and yard markings for reversing vehicles
- Age and condition of the equipment already in place
Options to discuss
Electric operator
A shaft-mounted or trolley operator with push-button controls, safety edge and photocells. Suits busy bays and can be interlocked with levellers, shelters and traffic lights.
Thicker insulated panels
Panels at the upper end of the common 40 to 80 mm range improve insulation for heated warehouses and temperature-controlled goods-in areas.
Regulations and approvals in England
In England, Approved Document L (2021) sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. That shapes door specification for sites in Burnley, so we confirm the requirement for your project and check what applies at survey before recommending a door.
Questions about sectional loading bay doors in Burnley
Will you deal with building control and planning for a project in Burnley?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Burnley, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Can you work alongside our main contractor on a new build in Burnley?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Can a sectional dock door be made to fit our existing opening?
Yes, sectional doors are made to measure, so they can be fitted to most existing dock openings. We measure the structural opening, headroom and side room at survey and choose a track to suit. Uneven reveals or a low lintel can usually be dealt with using packers, steel angles or a low-headroom track rather than building work.
Will the bay be out of action for long?
Usually only on installation day. The door is made to order before we book the fitting, so the old door stays in use until the new one is ready to go in. On sites with several bays we fit one opening at a time, keeping the rest of the dock running.
Sectional loading bay doors near Burnley
Distances are measured from Burnley. Nearby towns we cover include Nelson (3 miles), Colne (5 miles) and Accrington (6 miles), and other towns in the area are covered too.
Other loading bay services in Burnley
Full guide to sectional loading bay doors · Everything we do in Burnley
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Burnley site.