A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
How does this suit sites in Lanarkshire?
Ageing units around Lanarkshire sometimes have low lintels or pipework above the opening, which a low-headroom or high-lift track can be chosen to work around. Landlords preparing an industrial unit in Lanarkshire for a new tenant may choose to replace tired dock doors so the building is ready to trade from day one.
Warehouses across Lanarkshire that still rely on single-skin shutters may switch to insulated sectional doors when heating costs or cold goods-in areas become a problem.
The survey is free, the quote is written and the price is fixed: that is how every installation in Lanarkshire begins. We then manage the work from start to finish. Fitting is carried out by specialist installers under our management, phased so the operation keeps moving, and nights or weekends can be booked by arrangement. On the final day we test the equipment with you and hand over the operating and maintenance information.
Do sectional loading bay doors have to meet energy and safety rules?
Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
- Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
- Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.
What happens on site when a sectional dock door is installed?
Fitting a sectional dock door often takes around a day per opening once the door is on site, though very large doors or awkward fixings take longer. The bay is out of use while the work is under way.
A typical installation runs like this:
- The old door, if there is one, is taken down and removed from site.
- Steel angles or packers are fixed to the opening so the tracks run true.
- Tracks, springs and panels are assembled and the door is balanced.
- The operator, safety edge, photocells and controls are fitted and wired.
- The door is tested, adjusted and handed over.
Before we arrive you will need a clear area inside the opening for access equipment and the bay taken out of service. Electric doors also need a suitable isolated power supply near the door head, single or three-phase depending on the operator, which we confirm in the quote. On multi-door sites we work bay by bay so the rest of the dock keeps running.
Towns we cover in Lanarkshire
Each of the following towns in Lanarkshire has its own page on sectional loading bay doors, covering how we work and what to send us.
- East Kilbride
- Hamilton
- Cumbernauld
- Coatbridge
- Airdrie
- Motherwell
- Rutherglen
- Cambuslang
- Wishaw
- Bellshill
- Blantyre
- Viewpark
- Larkhall
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Planning, building control and safety law in Scotland
Energy standards for buildings in Scotland are set out in Section 6 of the Building Standards Technical Handbook. For new or replacement loading bay doors in Lanarkshire, we confirm the figure that applies to your project and check what applies at survey, rather than relying on rules written for elsewhere in the UK.
Questions
How long does installation take at a site in Lanarkshire?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Is VAT included in your guide prices for sectional loading bay doors?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Lanarkshire as everywhere else: for sectional loading bay doors, it is £2,400 to £5,200 per door, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
How is a sectional loading bay door locked?
A manual sectional door is usually locked with a slide bolt or shoot bolt on the inside, while an electric door is held closed by its operator. Because dock doors are secured from inside the building, extra locks are not often needed, but we can add bolts or a locking operator where security is a priority.
Can a manual sectional door be motorised later?
Often yes, if the door is sound and correctly balanced. An operator is fitted to the spring shaft or a trolley drive is fixed to the ceiling, and the door gets a safety edge and photocells at the same time. We check spring condition and balance first, because a motor should never be used to make up for a badly balanced door.
Other services in Lanarkshire
Full guide to sectional loading bay doors · All loading bay services in Lanarkshire