- Location
- Ammanford, Dyfed
- Main postcode district
- SA18
- Nearby (straight line)
- Gorseinon (9 miles), Llanelli (11 miles) and Neath (12 miles)
- Survey and quote
- Free, with a fixed written quote
A scissor lift table, often called a dock lift, is a powered platform raised and lowered by a hydraulic scissor mechanism to move goods between two levels. At a loading bay it lifts pallets and pallet trucks from ground level to the height of a trailer bed, making it a practical alternative to a raised dock where forming one is not possible.
What matters for scissor lift tables in Ammanford?
Sites in Ammanford replacing an ageing dock lift should look at its LOLER examination history, as repeated defects can signal that replacement is due. Older industrial buildings in Ammanford built with ground-level doors only can use a scissor lift table to load trailers without excavating the yard.
Where ground conditions in Ammanford make a deep recessed dock costly, a pit-mounted or surface-mounted lift table can be the more practical option.
The survey is free, the quote is written and the price is fixed: that is how every installation in Ammanford begins. We then manage the work from start to finish. Fitting is carried out by specialist installers under our management, phased so the operation keeps moving, and nights or weekends can be booked by arrangement. On the final day we test the equipment with you and hand over the operating and maintenance information.
Where are scissor lift tables used at loading bays?
Scissor lift tables are used wherever goods need to move between yard level and trailer height without a raised dock. They are a common answer for buildings that were never designed for articulated trailers.
- Ground-level doors: older units, workshops and retail back doors with no dock.
- Mixed fleets: the same lift can serve a van, a rigid lorry and an articulated trailer at different bed heights, typically from around 900 mm to 1,600 mm.
- Tight sites: where there is no room for a recessed approach ramp in the yard.
- Split levels: inside buildings with floors at different heights.
- Supplementing a dock: one lift beside a row of docks to handle vehicles that do not suit the levellers.
Our guide to converting a ground-level door into a loading dock compares lift tables with the other ways of reaching trailer height.
How much does a scissor lift table cost?
A scissor lift table for a loading bay typically costs £9,500 to £28,000 per lift, supplied and installed, excluding VAT. Smaller surface-mounted lifts sit towards the lower end; large, high-capacity pit lifts with gates and bridge plates sit towards the top.
What moves the price:
- Capacity: dock lifts are typically rated somewhere between 2,000 and 6,000 kg, and heavier ratings need a stronger mechanism.
- Platform size and travel: larger platforms and greater lift heights cost more.
- Mounting: pit-mounted or surface-mounted with a ramp.
- Safety equipment: bellows or skirts, toe guards, rails, gates and bridge plates.
- Electrics and access: supply to the power pack, delivery access and out-of-hours working.
Forming a pit, drainage and other groundworks are priced separately after survey. Following a free site survey, the written quote is the fixed price. VAT is added at the standard rate.
The same published guide range applies across Wales; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- How drivers are prevented from pulling away too early
- Bumper position and wear or damage on the dock face
- Wheel guide positions and yard markings for reversing vehicles
- Clear opening width and height for each door
- Gaps around trailers where heated or chilled air escapes
- Headroom above the opening and which track type will suit it
Options to discuss
Surface-mounted lift table
Stands on the existing floor with a short ramp on to the platform at its lowest height. No excavation, a quicker install and easier to relocate later.
Bridge plate
A hinged plate on the platform end that rests on the trailer bed during loading, bridging the gap so pallet trucks can cross smoothly between lift and trailer.
Planning, building control and safety law in Wales
Scissor lift tables and dock lifts in Wales can fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted, depending on the equipment and its use. For sites in Ammanford, your insurer or competent person will confirm the regime, and we check what applies at survey.
Questions about scissor lift tables in Ammanford
What details do you need from us to quote for scissor lift tables?
To get started, send the site address in Ammanford, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Ammanford, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
How do you price scissor lift tables for a site in Ammanford?
Guide budgets for supply and fit are £9,500 to £28,000 per lift, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Can a forklift drive on to a scissor lift table?
Only if the lift has been designed and rated for forklift traffic. Most loading bay lift tables are built for pallet trucks, and a forklift's weight and wheel loads need a much heavier platform and mechanism. Tell us how you load at survey so the lift is specified correctly.
What capacity of dock lift do I need?
A dock lift needs a capacity above the heaviest combined load it will carry, including the goods, the pallet truck and an operator if they ride on it. Loading bay lifts are typically rated somewhere between 2,000 and 6,000 kg. We work out the right rating from your loads at survey.
Scissor lift tables near Ammanford
We also cover towns near Ammanford, including Gorseinon (9 miles), Llanelli (11 miles) and Neath (12 miles). Each has its own page with the same services and process.
Other loading bay services in Ammanford
Full guide to scissor lift tables · Everything we do in Ammanford
Use the quote tool to tell us about the doors, levellers or shelters at your Ammanford site, and we will be in touch to arrange the next step.