- Location
- Stourport-on-Severn, Worcestershire
- Main postcode district
- DY13
- Nearby (straight line)
- Kidderminster (4 miles), Droitwich (7 miles) and Bromsgrove (9 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
What matters for roller shutter loading bay doors in Stourport-on-Severn?
Landlords refurbishing a vacant unit in Stourport-on-Severn may choose an insulated shutter where headroom is tight but a future tenant is likely to heat the building. Timber yards and builders merchants in Stourport-on-Severn handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks.
Every shutter we quote for a building in Stourport-on-Severn starts with a survey of the opening, the space above it and how often the door will run.
Before anything is ordered, we visit your site in Stourport-on-Severn for a free survey and then send a written quote with a fixed price. From that point we manage the installation, coordinating delivery, access and any other trades. Fitting is done by specialist installation engineers engaged and managed by us, at times that suit your operation, including out of hours where agreed. You get a tested installation, a demonstration for your team and the manufacturer documentation.
How much does a roller shutter loading bay door cost?
A roller shutter loading bay door typically costs £1,600 to £4,800 per door, excluding VAT, supply and fit. That usually makes it the most economical door for a dock opening, though the specification makes a big difference to where a door lands.
The price depends mainly on:
- Size: wider openings need a larger barrel, heavier laths and stronger brackets.
- Lath type: single-skin steel is the cheapest; foam-filled insulated laths and aluminium cost more.
- Operation: hand chain, or an electric motor with controls, safety edge and photocells.
- Wind resistance: end locks, deeper guides or heavier gauge laths for exposed openings.
- Finish: galvanised steel or a powder-coated colour, plus a hood box to protect the coil.
- Site work: stripping out an old shutter, repairing reveals, providing power and working out of hours.
The written quote that follows our free site survey fixes the price for the work described.
What safety and energy rules apply to roller shutters at a dock?
A dock roller shutter must be protected against falling, must not trap anyone if powered, and in a heated building may need insulated laths to meet energy rules.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Northern Ireland regulations of 1993, require upward-opening doors to have a device that stops them falling back. On a shutter this is usually a safety brake or anti-fall device on the barrel.
- Trapping: powered shutters need suitable features to prevent trapping, typically a safety edge and photocells, and a way to open by hand, such as a chain override, where needed.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access doors in new and replacement work. A single-skin steel shutter will not normally reach that figure. Wales, Scotland and Northern Ireland set their own rules, and we confirm the figure for your nation and project.
Our guide to energy rules for loading bay doors explains U-values in more detail.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Yard gradient and the slope of the approach to the dock
- Power supply at each bay, including three-phase availability
- Wheel guide positions and yard markings for reversing vehicles
- Traffic routes for vehicles and separation of pedestrians
- How often each door cycles during a typical shift
- Clear opening width and height for each door
Options to discuss
Single-skin steel shutter
Galvanised or powder-coated steel laths giving a strong, economical door for unheated stores, builders merchants and openings where security matters more than insulation.
Aluminium shutter
Lighter laths that resist corrosion, suited to coastal sites, washdown areas and large openings where a lighter curtain puts less strain on the motor.
Planning, building control and safety law in England
In England, Approved Document L (2021) sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. That shapes door specification for sites in Stourport-on-Severn, so we confirm the requirement for your project and check what applies at survey before recommending a door.
Questions about roller shutter loading bay doors in Stourport-on-Severn
Can you work alongside our main contractor on a new build in Stourport-on-Severn?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Is the site survey in Stourport-on-Severn free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Will you deal with building control and planning for a project in Stourport-on-Severn?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Can an existing manual shutter be motorised?
Often yes. If the barrel, end plates and curtain are in good condition, an external or tubular motor can be added with controls and safety devices. Older or heavier shutters sometimes need a stronger barrel first, and a badly worn curtain is usually better replaced at the same time.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
Roller shutter loading bay doors near Stourport-on-Severn
Sites close to Stourport-on-Severn get the same service, including those in Kidderminster (4 miles), Droitwich (7 miles) and Bromsgrove (9 miles), with every job run the same way.
Other loading bay services in Stourport-on-Severn
Full guide to roller shutter loading bay doors · Everything we do in Stourport-on-Severn
For a written price on loading bay work in Stourport-on-Severn, request a quote and include photos of the bay if you can.