- Location
- Lichfield, Staffordshire
- Main postcode district
- WS13
- Nearby (straight line)
- Burntwood (4 miles), Tamworth (6 miles) and Aldridge (7 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Where does this fit at a dock in Lichfield?
Docks that face an open yard in Lichfield can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it. Unheated stores and trade counters in Lichfield can suit a single-skin steel shutter, giving a secure dock door at a lower cost than an insulated sectional door.
If a manual shutter on a site in Lichfield is hard work to open several times a day, a new electric shutter or a retrofit motor may solve it.
We never ask you to commit before you have a fixed price. A free survey at your Lichfield site comes first, followed by a written quote. When the order goes ahead, we plan the installation around your operation, book any out-of-hours working you need and manage the specialist installation engineers on site. The job ends with a full test, a run-through for the people who will use the equipment and a set of handover documents.
What safety and energy rules apply to roller shutters at a dock?
A dock roller shutter must be protected against falling, must not trap anyone if powered, and in a heated building may need insulated laths to meet energy rules.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Northern Ireland regulations of 1993, require upward-opening doors to have a device that stops them falling back. On a shutter this is usually a safety brake or anti-fall device on the barrel.
- Trapping: powered shutters need suitable features to prevent trapping, typically a safety edge and photocells, and a way to open by hand, such as a chain override, where needed.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access doors in new and replacement work. A single-skin steel shutter will not normally reach that figure. Wales, Scotland and Northern Ireland set their own rules, and we confirm the figure for your nation and project.
Our guide to energy rules for loading bay doors explains U-values in more detail.
Can a roller shutter cope with high winds at an exposed dock?
Yes, if it is specified for the exposure. Wind pushes the curtain inwards or draws it outwards, and on a wide opening that load can pull laths out of their guides or bow the whole curtain.
For exposed docks we typically consider:
- End locks: clips on the ends of the laths that hold the curtain inside the guides under load.
- Deeper guides: give the end locks more to hold on to.
- Heavier gauge or profiled laths: stiffer across wide openings.
- Intermediate wind bars: horizontal reinforcement on very large shutters.
Openings that face open yards, sit at the end of a building or are funnelled between units tend to see the strongest gusts. We note orientation and surroundings at survey and choose a wind-resistant build where it is needed, rather than adding cost to every door on the site.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Control positions, isolators and any existing interlocks
- Yard gradient and the slope of the approach to the dock
- Access for deliveries, cranes or lifting equipment during installation
- Temperature requirements for chilled, frozen or ambient goods
- Forklift and pallet truck loads crossing the leveller platform
- Wheel guide positions and yard markings for reversing vehicles
Options to discuss
Wind-resistant build
End locks, deeper guides and heavier gauge laths for wide or exposed openings where gusts could pull the curtain out of its guides.
Electric operation with safety devices
An external or tubular motor with push-button controls, safety edge, photocells and a hand-chain override for use during a power cut.
Planning, building control and safety law in England
Workplace safety in England is regulated by HSE. For a loading bay in Lichfield, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about roller shutter loading bay doors in Lichfield
Can you work outside our normal operating hours in Lichfield?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
How do you price roller shutter loading bay doors for a site in Lichfield?
Guide budgets for supply and fit are £1,600 to £4,800 per door, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Is VAT included in your guide prices for roller shutter loading bay doors?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Staffordshire as everywhere else: for roller shutter loading bay doors, it is £1,600 to £4,800 per door, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
Can an existing manual shutter be motorised?
Often yes. If the barrel, end plates and curtain are in good condition, an external or tubular motor can be added with controls and safety devices. Older or heavier shutters sometimes need a stronger barrel first, and a badly worn curtain is usually better replaced at the same time.
Roller shutter loading bay doors near Lichfield
If your site is not in Lichfield itself, it may be near one of these: Burntwood (4 miles), Tamworth (6 miles) and Aldridge (7 miles). Pick the closest.
Other loading bay services in Lichfield
Full guide to roller shutter loading bay doors · Everything we do in Lichfield
Call us or request a quote online to talk through loading bay work at your site in Lichfield.