- Location
- Perth, Perth and Kinross
- Main postcode district
- PH1
- Nearby (straight line)
- Blairgowrie (14 miles), Crieff (16 miles) and Glenrothes (17 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Why do sites in Perth choose this?
Landlords refurbishing a vacant unit in Perth may choose an insulated shutter where headroom is tight but a future tenant is likely to heat the building. Docks that face an open yard in Perth can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it.
Timber yards and builders merchants in Perth handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks.
We never ask you to commit before you have a fixed price. A free survey at your Perth site comes first, followed by a written quote. When the order goes ahead, we plan the installation around your operation, book any out-of-hours working you need and manage the specialist installation engineers on site. The job ends with a full test, a run-through for the people who will use the equipment and a set of handover documents.
How is a roller shutter fitted to an existing loading bay opening?
A roller shutter is fitted either behind the opening on the inside face or between the reveals, with guides fixed down each side and the barrel mounted on brackets above. Fitting usually takes a day or less per opening once the shutter is on site.
The work normally includes:
- Removing and disposing of the old door or shutter.
- Checking the lintel and reveals will take the fixings, and adding steel packers if not.
- Fixing the guides, brackets and barrel, then running the curtain onto the barrel.
- Fitting the motor, controls, safety edge and photocells on electric shutters.
- Setting limits, testing the safety brake and demonstrating the manual override.
You will need to clear the area inside the opening and take the bay out of use. An electric shutter also needs a suitable isolated power supply near the barrel, which we can include in the quote if one is not already there.
How much does a roller shutter loading bay door cost?
A roller shutter loading bay door typically costs £1,600 to £4,800 per door, excluding VAT, supply and fit. That usually makes it the most economical door for a dock opening, though the specification makes a big difference to where a door lands.
The price depends mainly on:
- Size: wider openings need a larger barrel, heavier laths and stronger brackets.
- Lath type: single-skin steel is the cheapest; foam-filled insulated laths and aluminium cost more.
- Operation: hand chain, or an electric motor with controls, safety edge and photocells.
- Wind resistance: end locks, deeper guides or heavier gauge laths for exposed openings.
- Finish: galvanised steel or a powder-coated colour, plus a hood box to protect the coil.
- Site work: stripping out an old shutter, repairing reveals, providing power and working out of hours.
The written quote that follows our free site survey fixes the price for the work described.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Yard gradient and the slope of the approach to the dock
- Wind exposure at the dock, which affects door and shelter choice
- How often each door cycles during a typical shift
- Power supply at each bay, including three-phase availability
- Access for deliveries, cranes or lifting equipment during installation
- Dock height and the mix of trailers you load
Options to discuss
Electric operation with safety devices
An external or tubular motor with push-button controls, safety edge, photocells and a hand-chain override for use during a power cut.
Single-skin steel shutter
Galvanised or powder-coated steel laths giving a strong, economical door for unheated stores, builders merchants and openings where security matters more than insulation.
What do the rules in Scotland mean for the work?
HSE is the workplace safety regulator in Scotland. At a loading bay in Perth, doors need to satisfy regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, dock equipment must be kept safe under PUWER, and drivers must be prevented from pulling away too early. We check what applies at survey.
Questions about roller shutter loading bay doors in Perth
How long does installation take at a site in Perth?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
What details do you need from us to quote for roller shutter loading bay doors?
To get started, send the site address in Perth, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can you work alongside our main contractor on a new build in Perth?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
Do roller shutters work on cold store docks?
Roller shutters are rarely used as the main door on a cold store dock, because even insulated laths do not hold temperature as well as a purpose-made cold store door. They can work as an outer security door in front of an insulated door, or at ambient bays on the same site.
Roller shutter loading bay doors near Perth
Nearby places we cover, measured from Perth, include Blairgowrie (14 miles), Crieff (16 miles) and Glenrothes (17 miles). Ask if your own town is missing.
Other loading bay services in Perth
Full guide to roller shutter loading bay doors · Everything we do in Perth
Tell us what is happening at your Perth dock, what equipment is there and when it is used, and we will suggest the right next step.