- Location
- Bicester, Oxfordshire
- Main postcode districts
- OX25, OX26 and OX27
- Nearby (straight line)
- Oxford (11 miles), Cowley (12 miles) and Banbury (14 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
What should sites in Bicester consider?
Where a site in Bicester is exposed to salt air or regular washdown, aluminium laths or a good powder coat help slow corrosion on the curtain and guides. Unheated stores and trade counters in Bicester can suit a single-skin steel shutter, giving a secure dock door at a lower cost than an insulated sectional door.
Docks that face an open yard in Bicester can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it.
How does an installation in Bicester work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
How is a roller shutter fitted to an existing loading bay opening?
A roller shutter is fitted either behind the opening on the inside face or between the reveals, with guides fixed down each side and the barrel mounted on brackets above. Fitting usually takes a day or less per opening once the shutter is on site.
The work normally includes:
- Removing and disposing of the old door or shutter.
- Checking the lintel and reveals will take the fixings, and adding steel packers if not.
- Fixing the guides, brackets and barrel, then running the curtain onto the barrel.
- Fitting the motor, controls, safety edge and photocells on electric shutters.
- Setting limits, testing the safety brake and demonstrating the manual override.
You will need to clear the area inside the opening and take the bay out of use. An electric shutter also needs a suitable isolated power supply near the barrel, which we can include in the quote if one is not already there.
Is a roller shutter or a sectional door better for a loading bay?
A roller shutter is usually better where headroom is tight, budgets are limited or the building is unheated, while a sectional door is usually better for heated buildings and busy docks that open and close all day.
- Headroom: a shutter coils into a box above the opening; a sectional door needs track running back under the ceiling or up the wall.
- Insulation: insulated sectional panels generally outperform insulated laths.
- Speed: shutters are slower to open and close than most electric sectional doors.
- Security: a closed steel shutter is a robust barrier.
- Repairs: damaged laths can be replaced individually, just as a dented sectional panel can be swapped.
See sectional loading bay doors to compare the two. Where either would work, we can quote both so you can weigh price against performance.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Bumper position and wear or damage on the dock face
- Control positions, isolators and any existing interlocks
- Traffic routes for vehicles and separation of pedestrians
- Drainage on recessed or sloping dock approaches
- Gaps around trailers where heated or chilled air escapes
- How often each door cycles during a typical shift
Options to discuss
Wind-resistant build
End locks, deeper guides and heavier gauge laths for wide or exposed openings where gusts could pull the curtain out of its guides.
Aluminium shutter
Lighter laths that resist corrosion, suited to coastal sites, washdown areas and large openings where a lighter curtain puts less strain on the motor.
Which rules apply in England?
Workplace safety in England is regulated by HSE. For a loading bay in Bicester, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about roller shutter loading bay doors in Bicester
Will you deal with building control and planning for a project in Bicester?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Bicester site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Do you cover Bicester for roller shutter loading bay doors?
Yes. We take on roller shutter loading bay doors for businesses in Bicester and across Oxfordshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
What finish options are available?
Most dock shutters are supplied in galvanised steel or powder-coated in a standard colour, with other colours available at extra cost. A hood box over the coil protects it from dust and weather and gives a tidier finish inside. We confirm finish and colour in the written quote.
How long does a new roller shutter take to arrive?
Shutters are made to measure, so the lead time depends on size, lath type and finish, and we confirm it in the written quote. The existing door stays in use until the new shutter is ready, and installation is then booked for a time that suits your operation.
Roller shutter loading bay doors near Bicester
The same survey, quote and repair service is available in towns around Bicester, such as Oxford (11 miles), Cowley (12 miles) and Banbury (14 miles).
Other loading bay services in Bicester
Full guide to roller shutter loading bay doors · Everything we do in Bicester
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Bicester site.