A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
What should sites in Norfolk consider?
If a manual shutter on a site in Norfolk is hard work to open several times a day, a new electric shutter or a retrofit motor may solve it. Docks that face an open yard in Norfolk can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it.
Timber yards and builders merchants in Norfolk handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks.
It starts with a free site survey in Norfolk, where we measure the openings, check the dock and talk through how the bay is used. You then receive a fixed written quote. Once you accept, we manage the job: specialist installation engineers carry out the work under our management, planned around your deliveries, and out-of-hours working can be arranged. At handover we test everything with you and leave the documentation.
Is a roller shutter or a sectional door better for a loading bay?
A roller shutter is usually better where headroom is tight, budgets are limited or the building is unheated, while a sectional door is usually better for heated buildings and busy docks that open and close all day.
- Headroom: a shutter coils into a box above the opening; a sectional door needs track running back under the ceiling or up the wall.
- Insulation: insulated sectional panels generally outperform insulated laths.
- Speed: shutters are slower to open and close than most electric sectional doors.
- Security: a closed steel shutter is a robust barrier.
- Repairs: damaged laths can be replaced individually, just as a dented sectional panel can be swapped.
See sectional loading bay doors to compare the two. Where either would work, we can quote both so you can weigh price against performance.
How much does a roller shutter loading bay door cost?
A roller shutter loading bay door typically costs £1,600 to £4,800 per door, excluding VAT, supply and fit. That usually makes it the most economical door for a dock opening, though the specification makes a big difference to where a door lands.
The price depends mainly on:
- Size: wider openings need a larger barrel, heavier laths and stronger brackets.
- Lath type: single-skin steel is the cheapest; foam-filled insulated laths and aluminium cost more.
- Operation: hand chain, or an electric motor with controls, safety edge and photocells.
- Wind resistance: end locks, deeper guides or heavier gauge laths for exposed openings.
- Finish: galvanised steel or a powder-coated colour, plus a hood box to protect the coil.
- Site work: stripping out an old shutter, repairing reveals, providing power and working out of hours.
The written quote that follows our free site survey fixes the price for the work described.
Towns we cover in Norfolk
We provide roller shutter loading bay doors right across Norfolk. Pick the town closest to your site from the list below.
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Planning, building control and safety law in England
Workplace safety in England is regulated by HSE. For a loading bay in Norfolk, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Norfolk, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Can you work outside our normal operating hours in Norfolk?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
What finish options are available?
Most dock shutters are supplied in galvanised steel or powder-coated in a standard colour, with other colours available at extra cost. A hood box over the coil protects it from dust and weather and gives a tidier finish inside. We confirm finish and colour in the written quote.
Other services in Norfolk
Full guide to roller shutter loading bay doors · All loading bay services in Norfolk