- Location
- Poulton-le-Fylde, Lancashire
- Main postcode district
- FY6
- Nearby (straight line)
- Blackpool (3 miles), Thornton-Cleveleys (3 miles) and Lytham St Annes (6 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Is this right for your site in Poulton-le-Fylde?
Docks that face an open yard in Poulton-le-Fylde can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it. Every shutter we quote for a building in Poulton-le-Fylde starts with a survey of the opening, the space above it and how often the door will run.
If a manual shutter on a site in Poulton-le-Fylde is hard work to open several times a day, a new electric shutter or a retrofit motor may solve it.
If you are planning roller shutter loading bay doors for a site in Poulton-le-Fylde, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
Can a roller shutter cope with high winds at an exposed dock?
Yes, if it is specified for the exposure. Wind pushes the curtain inwards or draws it outwards, and on a wide opening that load can pull laths out of their guides or bow the whole curtain.
For exposed docks we typically consider:
- End locks: clips on the ends of the laths that hold the curtain inside the guides under load.
- Deeper guides: give the end locks more to hold on to.
- Heavier gauge or profiled laths: stiffer across wide openings.
- Intermediate wind bars: horizontal reinforcement on very large shutters.
Openings that face open yards, sit at the end of a building or are funnelled between units tend to see the strongest gusts. We note orientation and surroundings at survey and choose a wind-resistant build where it is needed, rather than adding cost to every door on the site.
How much does a roller shutter loading bay door cost?
A roller shutter loading bay door typically costs £1,600 to £4,800 per door, excluding VAT, supply and fit. That usually makes it the most economical door for a dock opening, though the specification makes a big difference to where a door lands.
The price depends mainly on:
- Size: wider openings need a larger barrel, heavier laths and stronger brackets.
- Lath type: single-skin steel is the cheapest; foam-filled insulated laths and aluminium cost more.
- Operation: hand chain, or an electric motor with controls, safety edge and photocells.
- Wind resistance: end locks, deeper guides or heavier gauge laths for exposed openings.
- Finish: galvanised steel or a powder-coated colour, plus a hood box to protect the coil.
- Site work: stripping out an old shutter, repairing reveals, providing power and working out of hours.
The written quote that follows our free site survey fixes the price for the work described.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- How drivers are prevented from pulling away too early
- Headroom above the opening and which track type will suit it
- Whether planning, building control or a building warrant may be needed
- Dock height and the mix of trailers you load
- Lighting inside trailers and at the dock face
- Age and condition of the equipment already in place
Options to discuss
Insulated lath shutter
Foam-filled twin-skin laths that improve thermal performance and reduce noise, for heated goods-in areas where headroom rules out a sectional door.
Single-skin steel shutter
Galvanised or powder-coated steel laths giving a strong, economical door for unheated stores, builders merchants and openings where security matters more than insulation.
What do the rules in England mean for the work?
Workplace safety in England is regulated by HSE. For a loading bay in Poulton-le-Fylde, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about roller shutter loading bay doors in Poulton-le-Fylde
Will you deal with building control and planning for a project in Poulton-le-Fylde?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Is the site survey in Poulton-le-Fylde free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Is VAT included in your guide prices for roller shutter loading bay doors?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Lancashire as everywhere else: for roller shutter loading bay doors, it is £1,600 to £4,800 per door, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
What finish options are available?
Most dock shutters are supplied in galvanised steel or powder-coated in a standard colour, with other colours available at extra cost. A hood box over the coil protects it from dust and weather and gives a tidier finish inside. We confirm finish and colour in the written quote.
Can an existing manual shutter be motorised?
Often yes. If the barrel, end plates and curtain are in good condition, an external or tubular motor can be added with controls and safety devices. Older or heavier shutters sometimes need a stronger barrel first, and a badly worn curtain is usually better replaced at the same time.
Roller shutter loading bay doors near Poulton-le-Fylde
Other towns within reach of Poulton-le-Fylde on our coverage list include Blackpool (3 miles), Thornton-Cleveleys (3 miles) and Lytham St Annes (6 miles), all covered on the same terms.
Other loading bay services in Poulton-le-Fylde
Full guide to roller shutter loading bay doors · Everything we do in Poulton-le-Fylde
Get in touch about loading bay doors and dock equipment in Poulton-le-Fylde: call, email or use the quote tool.