- Location
- Feltham, Greater London
- Main postcode district
- TW13
- Nearby (straight line)
- Ashford (2 miles), Hounslow (3 miles) and Sunbury-on-Thames (3 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
What matters for roller shutter loading bay doors in Feltham?
If a manual shutter on a site in Feltham is hard work to open several times a day, a new electric shutter or a retrofit motor may solve it. Where a site in Feltham is exposed to salt air or regular washdown, aluminium laths or a good powder coat help slow corrosion on the curtain and guides.
Unheated stores and trade counters in Feltham can suit a single-skin steel shutter, giving a secure dock door at a lower cost than an insulated sectional door.
We never ask you to commit before you have a fixed price. A free survey at your Feltham site comes first, followed by a written quote. When the order goes ahead, we plan the installation around your operation, book any out-of-hours working you need and manage the specialist installation engineers on site. The job ends with a full test, a run-through for the people who will use the equipment and a set of handover documents.
In the wider area around Feltham, Heathrow's logistics and air-cargo cluster is close by. Docks with frequent trailer movements put more cycles on doors and levellers, which is why planned servicing matters.
What safety and energy rules apply to roller shutters at a dock?
A dock roller shutter must be protected against falling, must not trap anyone if powered, and in a heated building may need insulated laths to meet energy rules.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Northern Ireland regulations of 1993, require upward-opening doors to have a device that stops them falling back. On a shutter this is usually a safety brake or anti-fall device on the barrel.
- Trapping: powered shutters need suitable features to prevent trapping, typically a safety edge and photocells, and a way to open by hand, such as a chain override, where needed.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access doors in new and replacement work. A single-skin steel shutter will not normally reach that figure. Wales, Scotland and Northern Ireland set their own rules, and we confirm the figure for your nation and project.
Our guide to energy rules for loading bay doors explains U-values in more detail.
Which lath should I choose: single skin, insulated or aluminium?
Choose single-skin steel for unheated buildings where cost and strength matter most, insulated laths where the building is heated, and aluminium where weight or corrosion is the main concern.
- Single-skin steel: strong and economical, ideal for unheated stores, trade counters and secure external openings, but it offers little insulation.
- Insulated steel laths: twin-skin laths filled with foam improve thermal performance and reduce noise. The coil is larger, so the box above the opening is bigger.
- Aluminium laths: lighter and corrosion resistant, useful in coastal or washdown environments, and easier on the motor at large openings.
- Perforated or punched laths: let light and air through while keeping the opening secure, better suited to internal cages than external docks.
Lath gauge and profile matter too. Heavier gauges resist forklift knocks and wind better, and we specify them for wide or exposed openings.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Dock height and the mix of trailers you load
- Yard gradient and the slope of the approach to the dock
- Asbestos register and any other site hazard information
- Gaps around trailers where heated or chilled air escapes
- Condition of any existing leveller pit, kerb angles and pit drainage
- How drivers are prevented from pulling away too early
Options to discuss
Wind-resistant build
End locks, deeper guides and heavier gauge laths for wide or exposed openings where gusts could pull the curtain out of its guides.
Electric operation with safety devices
An external or tubular motor with push-button controls, safety edge, photocells and a hand-chain override for use during a power cut.
What do the rules in England mean for the work?
Sites in Feltham fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about roller shutter loading bay doors in Feltham
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Feltham site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
How long does installation take at a site in Feltham?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Can you work alongside our main contractor on a new build in Feltham?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
Can individual damaged laths be replaced?
Yes, damaged laths can usually be cut out and replaced without changing the whole curtain, provided matching laths are still available. If damage spreads across many laths or the guides are bent, a new curtain is often more economical. Lath repairs are carried out on a chargeable visit with the price agreed first.
Roller shutter loading bay doors near Feltham
If your site is not in Feltham itself, it may be near one of these: Ashford (2 miles), Hounslow (3 miles) and Sunbury-on-Thames (3 miles). Pick the closest.
Other loading bay services in Feltham
Full guide to roller shutter loading bay doors · Everything we do in Feltham
Request a quote for your loading bay in Feltham, attaching photos of the dock, the equipment and any damage.