- Location
- Tewkesbury, Gloucestershire
- Main postcode district
- GL20
- Nearby (straight line)
- Cheltenham (7 miles), Gloucester (9 miles) and Great Malvern (11 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Where does this fit at a dock in Tewkesbury?
Timber yards and builders merchants in Tewkesbury handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks. Unheated stores and trade counters in Tewkesbury can suit a single-skin steel shutter, giving a secure dock door at a lower cost than an insulated sectional door.
If a manual shutter on a site in Tewkesbury is hard work to open several times a day, a new electric shutter or a retrofit motor may solve it.
We keep the process simple for sites in Tewkesbury. A free survey tells us what the dock needs; a fixed written quote tells you what it will cost and what is included. We then organise the installation, with specialist engineers under our management and a programme agreed around your shifts. Night and weekend work is available by arrangement. Before we leave, the new equipment is tested, demonstrated and handed over with its documentation.
What safety and energy rules apply to roller shutters at a dock?
A dock roller shutter must be protected against falling, must not trap anyone if powered, and in a heated building may need insulated laths to meet energy rules.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Northern Ireland regulations of 1993, require upward-opening doors to have a device that stops them falling back. On a shutter this is usually a safety brake or anti-fall device on the barrel.
- Trapping: powered shutters need suitable features to prevent trapping, typically a safety edge and photocells, and a way to open by hand, such as a chain override, where needed.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access doors in new and replacement work. A single-skin steel shutter will not normally reach that figure. Wales, Scotland and Northern Ireland set their own rules, and we confirm the figure for your nation and project.
Our guide to energy rules for loading bay doors explains U-values in more detail.
Which lath should I choose: single skin, insulated or aluminium?
Choose single-skin steel for unheated buildings where cost and strength matter most, insulated laths where the building is heated, and aluminium where weight or corrosion is the main concern.
- Single-skin steel: strong and economical, ideal for unheated stores, trade counters and secure external openings, but it offers little insulation.
- Insulated steel laths: twin-skin laths filled with foam improve thermal performance and reduce noise. The coil is larger, so the box above the opening is bigger.
- Aluminium laths: lighter and corrosion resistant, useful in coastal or washdown environments, and easier on the motor at large openings.
- Perforated or punched laths: let light and air through while keeping the opening secure, better suited to internal cages than external docks.
Lath gauge and profile matter too. Heavier gauges resist forklift knocks and wind better, and we specify them for wide or exposed openings.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Asbestos register and any other site hazard information
- Drainage on recessed or sloping dock approaches
- Wind exposure at the dock, which affects door and shelter choice
- Bumper position and wear or damage on the dock face
- Age and condition of the equipment already in place
- Yard gradient and the slope of the approach to the dock
Options to discuss
Wind-resistant build
End locks, deeper guides and heavier gauge laths for wide or exposed openings where gusts could pull the curtain out of its guides.
Electric operation with safety devices
An external or tubular motor with push-button controls, safety edge, photocells and a hand-chain override for use during a power cut.
Regulations and approvals in England
Sites in Tewkesbury fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about roller shutter loading bay doors in Tewkesbury
Can you work alongside our main contractor on a new build in Tewkesbury?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
What details do you need from us to quote for roller shutter loading bay doors?
To get started, send the site address in Tewkesbury, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
How long does installation take at a site in Tewkesbury?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Can individual damaged laths be replaced?
Yes, damaged laths can usually be cut out and replaced without changing the whole curtain, provided matching laths are still available. If damage spreads across many laths or the guides are bent, a new curtain is often more economical. Lath repairs are carried out on a chargeable visit with the price agreed first.
Can an existing manual shutter be motorised?
Often yes. If the barrel, end plates and curtain are in good condition, an external or tubular motor can be added with controls and safety devices. Older or heavier shutters sometimes need a stronger barrel first, and a badly worn curtain is usually better replaced at the same time.
Roller shutter loading bay doors near Tewkesbury
Nearby places we cover, measured from Tewkesbury, include Cheltenham (7 miles), Gloucester (9 miles) and Great Malvern (11 miles). Ask if your own town is missing.
Other loading bay services in Tewkesbury
Full guide to roller shutter loading bay doors · Everything we do in Tewkesbury
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Tewkesbury site.