A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Where does this fit at a dock in Dorset?
Every shutter we quote for a building in Dorset starts with a survey of the opening, the space above it and how often the door will run. Docks that face an open yard in Dorset can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it.
Timber yards and builders merchants in Dorset handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks.
Here is what happens after you contact us about a site in Dorset. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
How much does a roller shutter loading bay door cost?
A roller shutter loading bay door typically costs £1,600 to £4,800 per door, excluding VAT, supply and fit. That usually makes it the most economical door for a dock opening, though the specification makes a big difference to where a door lands.
The price depends mainly on:
- Size: wider openings need a larger barrel, heavier laths and stronger brackets.
- Lath type: single-skin steel is the cheapest; foam-filled insulated laths and aluminium cost more.
- Operation: hand chain, or an electric motor with controls, safety edge and photocells.
- Wind resistance: end locks, deeper guides or heavier gauge laths for exposed openings.
- Finish: galvanised steel or a powder-coated colour, plus a hood box to protect the coil.
- Site work: stripping out an old shutter, repairing reveals, providing power and working out of hours.
The written quote that follows our free site survey fixes the price for the work described.
Is a roller shutter or a sectional door better for a loading bay?
A roller shutter is usually better where headroom is tight, budgets are limited or the building is unheated, while a sectional door is usually better for heated buildings and busy docks that open and close all day.
- Headroom: a shutter coils into a box above the opening; a sectional door needs track running back under the ceiling or up the wall.
- Insulation: insulated sectional panels generally outperform insulated laths.
- Speed: shutters are slower to open and close than most electric sectional doors.
- Security: a closed steel shutter is a robust barrier.
- Repairs: damaged laths can be replaced individually, just as a dented sectional panel can be swapped.
See sectional loading bay doors to compare the two. Where either would work, we can quote both so you can weigh price against performance.
Towns we cover in Dorset
We take enquiries about roller shutter loading bay doors from across Dorset. These are the towns with their own pages:
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Which rules apply in England?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Dorset. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions
How do you price roller shutter loading bay doors for a site in Dorset?
Guide budgets for supply and fit are £1,600 to £4,800 per door, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
What details do you need from us to quote for roller shutter loading bay doors?
To get started, send the site address in Dorset, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can an existing manual shutter be motorised?
Often yes. If the barrel, end plates and curtain are in good condition, an external or tubular motor can be added with controls and safety devices. Older or heavier shutters sometimes need a stronger barrel first, and a badly worn curtain is usually better replaced at the same time.
Do roller shutters work on cold store docks?
Roller shutters are rarely used as the main door on a cold store dock, because even insulated laths do not hold temperature as well as a purpose-made cold store door. They can work as an outer security door in front of an insulated door, or at ambient bays on the same site.
Other services in Dorset
Full guide to roller shutter loading bay doors · All loading bay services in Dorset