Loading houses in Reading

Location: Reading, Berkshire
Main postcode districts: RG1, RG6 and RG30
Nearby (straight line): Lower Earley (3 miles), Wokingham (7 miles) and Crowthorne (10 miles)
Survey and quote: Free, with a fixed written quote

Loading houses, in short

A loading house is an insulated steel structure built against the outside wall of a building, containing a dock leveller and usually a shelter or seal at its front. The building door closes at the wall line, while trailers dock against the house. Loading houses suit buildings whose floor is at dock height but which have no room inside for a leveller pit.

What should sites in Reading consider?

Where a yard in Reading is narrow, an angled loading house lets trailers approach on a diagonal and can sometimes fit more bays along one wall. Units in Reading with floors at dock height but no room for an internal leveller pit are typical candidates for an external loading house.

Any loading house proposed in Reading needs its planning and building control position checked, which we look at during the site survey before quoting.

A single contact at Loading Bay Doors handles your project in Reading from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.

Does a loading house need planning permission or building approval?

A loading house can need planning permission, because it is a new external structure, so we check this at survey rather than assuming it is not needed. The answer depends on the site, the size of the house and any planning conditions already on the building.

Forming a new opening in the building wall is a structural alteration that may need approval. In England and Wales that means Building Regulations approval, in Scotland a building warrant, and in Northern Ireland building control approval.

Energy rules can also apply to the door in the building wall. In England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland have their own energy rules, and we confirm the figure that applies to your nation and project.

The leveller inside the house is specified to BS EN 1398:2009, the dock leveller safety standard. Our guide to loading houses explained goes through the approvals in more detail.

When is a loading house better than an internal dock?

A loading house is usually the better option when the building floor is already at dock height but there is no practical way to form a leveller pit inside. It moves the whole dock outside the wall, leaving the internal floor clear.

No room inside: racking, production lines or mezzanines sit right up to the wall.
Difficult slab: the floor slab carries services or is unsuited to breaking out for a pit.
Thermal control: the building door closes at the wall line, so the leveller sits outside the heated or chilled space when no trailer is docked.
Security: the building can be closed at the wall line while the house itself stays open to the yard.
Narrow yards: an angled house lets trailers approach on a diagonal and can fit more bays along one wall.

Where the building floor is at yard level, a loading house alone will not solve the height difference, and a recessed approach or lift table is usually needed instead.

Guide price, Reading

£14,500–£32,000 per house, ex VAT

The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.

What does the free survey cover?

Temperature requirements for chilled, frozen or ambient goods
Age and condition of the equipment already in place
Condition of any existing leveller pit, kerb angles and pit drainage
Headroom above the opening and which track type will suit it
How often each door cycles during a typical shift
Wall and steel structure for door, shelter and bumper fixings

Options to discuss

Shelter or seal front

A retractable or inflatable shelter, or a foam dock seal, across the front of the house, chosen to suit your trailers and how tightly the bay needs to seal.

Angled loading house

Set at an angle to the wall so trailers approach on a diagonal, useful on narrow yards and sometimes allowing more bays to fit along a single elevation.

What do the rules in England mean for the work?

Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Reading. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.

Questions about loading houses in Reading

Which building and safety rules apply to a site in Reading?

It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Reading, we check what applies at survey and design to it.

What details do you need from us to quote for loading houses?

To get started, send the site address in Reading, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.

Is VAT included in your guide prices for loading houses?

No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Berkshire as everywhere else: for loading houses, it is £14,500 to £32,000 per house, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.

Is a loading house cheaper than forming an internal pit?

Not always. A loading house includes a whole steel structure, so the equipment cost is higher, but it avoids breaking out the slab and losing internal floor space. The best comparison is made at survey, taking account of racking, services under the floor and how the building will be used.

How long does a loading house take to install?

The programme depends mainly on foundation works and manufacturing lead times, and we set it out in writing with the quote. On site, foundations must cure before the frame goes up, and the rest of the work follows in sequence. We agree dates with you so other bays can keep working.

Loading houses near Reading

Sites close to Reading get the same service, including those in Lower Earley (3 miles), Wokingham (7 miles) and Crowthorne (10 miles), with every job run the same way.