- Location
- Pembroke Dock, Dyfed
- Main postcode district
- SA72
- Nearby (straight line)
- Milford Haven (4 miles), Haverfordwest (8 miles) and Carmarthen (30 miles)
- Visit pricing
- Agreed in writing before we attend
Loading bay door repair covers diagnosing and fixing faults on industrial dock doors, including sectional overhead doors, roller shutters and high-speed fabric doors. Typical work includes replacing broken springs and cables, damaged panels, rollers and hinges, repairing motors and control panels, and restoring safety devices such as safety edges and photocells so the door works safely and closes securely again.
Where does this fit at a dock in Pembroke Dock?
If a dock door at a site in Pembroke Dock will not close, tell us about any security concerns so the visit and making the building secure can be planned together. Repair requests from Pembroke Dock are handled in the same way as anywhere in the UK, with the price agreed before anyone attends and a written report afterwards.
High-speed doors on internal openings at sites near Pembroke Dock can lose their curtain from the guides after a knock, which is usually a straightforward reset and check.
Tell us what has gone wrong at your Pembroke Dock site and, if you can, send photos of the fault and any labels on the equipment. We then confirm the visit price in writing, and nobody attends until you have agreed it. On site, the engineer diagnoses and repairs what was agreed; anything extra is quoted first, never added without your say-so. A written report follows, covering findings, work carried out and recommendations.
What happens when an engineer attends to repair a dock door?
When an engineer attends, the bay is closed, the door is made safe and isolated, and the fault is diagnosed before any repair starts. Only the affected bay needs to stop.
- Isolate the bay: no trailer on the dock, the leveller parked and the area around the door coned off.
- Make safe: the door is electrically isolated and locked off, and spring tension is released or the door supported before work begins.
- Diagnose: the engineer confirms the cause. Anything beyond the agreed scope is quoted before it is done.
- Repair and test: parts are fitted, the door is balanced and every safety device is tested.
If a door cannot be repaired on the first visit, for example because a matched panel must be ordered, it is left secure where possible and a return visit agreed.
It helps if you can provide access to the bay, a contact on site, any labels showing the door size and serial details, and permit-to-work information. To arrange a visit, contact us with a description of the fault.
Should I repair or replace an old loading bay door?
Repair is usually the right choice when the door structure, tracks and most panels are sound and parts are available. Replacement starts to make more sense when faults keep recurring or the door no longer suits the building.
Points that favour repair:
- a single failed component, such as a spring, cable or photocell;
- impact damage limited to one or two panels;
- a door that is otherwise in good condition and suits the operation.
Points that favour replacement:
- parts for an obsolete door are no longer available;
- widespread panel damage, corrosion or distorted tracks;
- repeated breakdowns that cost more than they save;
- an uninsulated door on a heated or chilled building.
In England, a replacement door should meet the Approved Document L limiting U-value of 1.3 W/m²K for large doors; Wales, Scotland and Northern Ireland have their own energy rules. If the written report after a repair recommends replacement, we can quote for it separately.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What we look at around the bay
- Previous service and inspection records, where available
- Track alignment, rollers and wall fixings
- Safety edges, photocells and light curtains
- Dock bumpers for missing rubber or loose fixings
- Door springs, cables and drums for wear or damage
- Anti-fall device on upward-opening doors
Options to discuss
High-speed door curtain repairs
Resetting breakaway curtains, replacing torn fabric and repairing guides and drives on fast-acting doors used at docks and internal openings.
Safety device repairs
Replacing or realigning safety edges, photocells and light curtains so the door stops and reverses when it should, then testing every device before handover.
Planning, building control and safety law in Wales
Wales has its own energy requirements for buildings, set out in Approved Document L for Wales. For new or replacement loading bay doors in Pembroke Dock, we confirm the figure that applies to your project rather than assuming the English one, and we check what applies before any work starts before a door is specified.
Questions about loading bay door repairs in Pembroke Dock
What happens if the engineer finds the equipment unsafe?
If equipment is found to be unsafe, the engineer will tell you straight away and recommend that it is isolated and taken out of use until it is repaired. That is recorded in the written report. We then quote the repair so you can decide how to proceed. Keeping an unsafe door or leveller in service puts people at risk, so we will always raise it.
Do you provide a written report after each visit?
Yes. After every repair or service visit to a site in Pembroke Dock, you receive a written report setting out what was checked, what was found, what work was carried out and anything that still needs attention, with a quote for further work where needed. The report is useful for your maintenance records and for discussions with your insurer or inspector.
How is a repair or service visit in Pembroke Dock priced?
Repair and service visits are chargeable, and the price is agreed in writing before anyone attends. For loading bay door repairs, the guide budget is £180 to £1,400 per repair, excluding VAT. The exact figure depends on the fault, parts, access and timing. If the engineer finds further work on the day, it is quoted for your approval before it is carried out.
Is it safe to use a door with a broken spring?
No. A door with a broken spring or cable should be taken out of use and the area kept clear, because the door may be heavy, unbalanced or at risk of dropping. Springs store a great deal of energy, so do not try to adjust or remove them yourself.
What happens if the door cannot be repaired?
If a door cannot be repaired economically, or parts are no longer available, the written report explains why. We make the door as safe and secure as possible in the meantime and can quote separately for a replacement, so you can compare the options.
Loading bay door repairs near Pembroke Dock
If your site is not in Pembroke Dock itself, it may be near one of these: Milford Haven (4 miles), Haverfordwest (8 miles) and Carmarthen (30 miles). Pick the closest.
Other loading bay services in Pembroke Dock
Full guide to loading bay door repairs · Everything we do in Pembroke Dock
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Pembroke Dock site.