- Location
- Burntwood, Staffordshire
- Main postcode district
- WS7
- Nearby (straight line)
- Great Wyrley (4 miles), Lichfield (4 miles) and Cannock (4 miles)
- Survey and quote
- Free, with a fixed written quote
A loading bay door automation package is an electric operator, control panel and set of safety devices fitted to an existing manual sectional door or roller shutter so it opens and closes at the press of a button. Once motorised, the door is a power-operated door, so it needs protection against trapping, such as a safety edge and photocells, and a way to be opened by hand if the power fails.
What should sites in Burntwood consider?
Teams working on cold or wet docks in Burntwood tend to leave doors open if they are hard to operate, so motorising them can help keep heat in. On older units in Burntwood where the original doors are still sound, automation keeps the existing door working while removing the effort of hand chains.
Heavy shutters on trade and merchant sites in Burntwood can be tiring to open by hand, which is where an external chain-drive motor earns its place.
Our part of the job in Burntwood is to survey, quote and manage; the fitting itself is done by specialist installation engineers working under our management. The survey and the written quote are free. Once the fixed price is accepted, we agree dates that work around your deliveries and shifts, including out-of-hours working where needed. Every installation is tested before handover, and you receive the documentation for each item fitted.
What is involved in fitting a motor to an existing dock door?
Fitting a motor to an existing dock door usually takes a few hours to a day per door, and starts with checking that the door itself is safe to automate.
- The door is checked for balance, spring condition, cable wear and track alignment.
- The operator is mounted on the shaft, ceiling rail or barrel bracket.
- The control panel is fixed in a safe position with a clear view of the door.
- A safety edge is fitted to the bottom rail and photocells are set across the opening.
- Limits, forces and controls are set, then the door is tested against the relevant safety checks.
You will need to provide a suitable isolated power supply near the door, or ask us to include it, and keep the door out of use during the work. Single-phase supplies suit many operators, but larger industrial operators may need three-phase power, which we confirm at survey.
How much does it cost to motorise a loading bay door?
Automating an existing loading bay door typically costs £1,100 to £2,400 per door, excluding VAT, supply and fit. That covers the operator, control panel, safety devices, wiring at the door and commissioning.
What moves the price:
- Door type and weight: heavy shutters and large sectional doors need more powerful operators.
- Operator type: shaft-mounted, trolley, tubular or external chain-drive.
- Control mode: hold-to-run controls need fewer safety devices than impulse or automatic operation.
- Safety devices: safety edge, photocells and, for automatic closing, additional sensing.
- Extras: remote controls, pull cords, induction loops and interlocks with levellers or traffic lights.
- Power: whether a suitable isolated supply already exists near the door.
If the door needs work before it can be motorised, such as new springs or rollers, we price that separately so you can see each cost. The written quote after a free site survey is the fixed price.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Whether planning, building control or a building warrant may be needed
- Wind exposure at the dock, which affects door and shelter choice
- Wall and steel structure for door, shelter and bumper fixings
- Dock height and the mix of trailers you load
- Control positions, isolators and any existing interlocks
- Power supply at each bay, including three-phase availability
Options to discuss
Tubular or external shutter motor
A motor inside the barrel for small and medium shutters, or a side-mounted chain-drive unit for large, heavy shutters at busy openings.
Shaft-mounted operator
A compact industrial motor that fits directly onto the spring shaft of a sectional door, suited to heavy dock doors and bays that run many cycles a day.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Burntwood. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about loading bay door automation in Burntwood
Can you work alongside our main contractor on a new build in Burntwood?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Burntwood, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
How do you price loading bay door automation for a site in Burntwood?
Guide budgets for supply and fit are £1,100 to £2,400 per door, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Do we need a three-phase supply?
Not always. Many operators for small and medium doors run on a single-phase supply, while larger industrial operators for heavy dock doors often need three-phase power. We confirm the supply your door needs at survey and can include any electrical work in the written quote.
Can any manual door be motorised?
No, only doors that are sound, balanced and run smoothly by hand should be motorised. Doors with weak springs, damaged panels, bent laths or obsolete parts may need repair first, or may be better replaced. We check this at survey and tell you which applies before quoting.
Loading bay door automation near Burntwood
Businesses outside Burntwood may find their nearest town in this list: Great Wyrley (4 miles), Lichfield (4 miles) and Cannock (4 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Burntwood
Full guide to loading bay door automation · Everything we do in Burntwood
Have photos of the door, leveller or shelter? Send them with your enquiry and we can give a clearer answer for your Burntwood site.