- Location
- Burton upon Trent, Staffordshire
- Main postcode district
- DE14
- Nearby (straight line)
- Swadlincote (4 miles), Derby (11 miles) and Lichfield (12 miles)
- Visit pricing
- Agreed in writing before we attend
Dock shelter and seal repair covers restoring the weather seal around a docked trailer. Typical work includes replacing torn side and head curtains, worn foam seal pads and their covers, top pads and guide strips, repairing or replacing airbags and blowers on inflatable shelters, and straightening or replacing bent shelter frames, so the bay closes the gap between building and trailer again.
Is this right for your site in Burton upon Trent?
Older retractable shelters on estates around Burton upon Trent can often be refurbished with new curtains and pads rather than replaced, provided the frame is still sound. If tenants change at a unit in Burton upon Trent, checking the shelters and seals is sensible, because a new fleet may not suit the old curtain sizes.
Curtains tearing at the corners at docks in Burton upon Trent can be a sign that taller or wider trailers are arriving than the shelter was sized for.
Tell us what has gone wrong at your Burton upon Trent site and, if you can, send photos of the fault and any labels on the equipment. We then confirm the visit price in writing, and nobody attends until you have agreed it. On site, the engineer diagnoses and repairs what was agreed; anything extra is quoted first, never added without your say-so. A written report follows, covering findings, work carried out and recommendations.
What happens on site during a shelter or seal repair?
During a shelter or seal repair the bay is closed to trailers while the engineer works from the yard, often using access equipment for the head curtain and top pad. Neighbouring bays can usually keep working, although access equipment may need space in front of them.
- Measure: where parts are made to measure, the shelter or seal is measured first and the parts ordered.
- Close the bay: no trailer on the dock and the yard area coned off.
- Isolate: on inflatable shelters, the blower supply is isolated and locked off.
- Replace parts: old curtains, pads or airbags are removed and new ones fitted, with frames straightened or replaced as agreed.
- Check the seal: overlap and compression are checked, with a trailer docked if one is available.
It helps if you can provide photos with a trailer docked, yard space for access equipment, a contact who can arrange electrical isolation and an agreed time when the bay can be released.
Why is my dock shelter or seal letting in draughts?
A dock shelter or seal lets in draughts when the material that should press against the trailer is torn, worn, too short or no longer in the right place. Daylight around a docked trailer is the clearest sign.
- Torn or shrunk curtains: side curtains no longer overlap the trailer sides.
- Short head curtain: taller trailers than the shelter was sized for leave a gap across the top.
- Flattened seal pads: foam that has lost its spring no longer closes the gap.
- Worn pad covers: exposed foam soaks up water and breaks down faster.
- Bent frame: a retractable shelter frame that no longer returns square.
- Airbag or blower fault: inflatable shelters that inflate slowly or lose pressure.
- Trailer position: off-centre parking or worn bumpers that let trailers crush one side.
On chilled docks, gaps also show up as condensation, ice on the dock floor or frost around the door.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What else does the engineer check at the bay?
- Shelter curtains, frames and side pads for tears
- Pit frame welds, platform cracks and structural damage
- Door panels, side seals and bottom rubbers
- Lip hinge, lip extension and lip support operation
- Safety edges, photocells and light curtains
- Door springs, cables and drums for wear or damage
Options to discuss
Frame repairs
Straightening or replacing bent arms, springs and frames on retractable shelters damaged by off-centre trailers, so the shelter returns square after each docking.
Seal pad refurbishment
Replacing worn foam pads, or just their covers where the foam is still sound, including tougher facings on the areas where trailers rub most.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Burton upon Trent, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies before any work starts and design the bay accordingly.
Questions about dock shelter and seal repairs in Burton upon Trent
What happens if the engineer finds the equipment unsafe?
If equipment is found to be unsafe, the engineer will tell you straight away and recommend that it is isolated and taken out of use until it is repaired. That is recorded in the written report. We then quote the repair so you can decide how to proceed. Keeping an unsafe door or leveller in service puts people at risk, so we will always raise it.
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
What information helps before a repair visit?
Photos or a short video of the fault are the most useful thing you can send, along with the make and model from the data plate, a description of what happens when the equipment is operated and any error codes. For a site in Burton upon Trent, also tell us about access, parking and site rules. With that, we can price the visit and bring the likely parts.
How is the price for a shelter or seal repair agreed?
You describe the damage and send photos, and we agree the visit price in writing before anyone attends. For made-to-measure parts that may include a measuring visit. Any extra work found on site is quoted and only carried out once you approve it.
Can you replace just the curtains on a dock shelter?
Yes. If the frame is still sound, the side and head curtains can be replaced on their own, which is the most common shelter repair. Curtains are usually made to measure, so the shelter is measured first and the new curtains fitted on a second visit, with both visits priced in advance.
Dock shelter and seal repairs near Burton upon Trent
Close neighbours of Burton upon Trent with their own pages here: Swadlincote (4 miles), Derby (11 miles) and Lichfield (12 miles). Choose one to see coverage details for that town.
Other loading bay services in Burton upon Trent
Full guide to dock shelter and seal repairs · Everything we do in Burton upon Trent
Use the quote tool to tell us about the doors, levellers or shelters at your Burton upon Trent site, and we will be in touch to arrange the next step.