- Location
- Wellington, Shropshire
- Main postcode district
- TF1
- Nearby (straight line)
- Telford (3 miles), Shrewsbury (10 miles) and Stafford (18 miles)
- Visit pricing
- Agreed in writing before we attend
Dock shelter and seal repair covers restoring the weather seal around a docked trailer. Typical work includes replacing torn side and head curtains, worn foam seal pads and their covers, top pads and guide strips, repairing or replacing airbags and blowers on inflatable shelters, and straightening or replacing bent shelter frames, so the bay closes the gap between building and trailer again.
Is this right for your site in Wellington?
Curtains tearing at the corners at docks in Wellington can be a sign that taller or wider trailers are arriving than the shelter was sized for. Repairs to shelters and seals in Wellington follow the same process as anywhere else in the UK, with the visit price agreed in writing first.
Inflatable shelters at food sites in Wellington depend on blowers and airbags working properly, and a slow-inflating shelter is worth checking before it fails.
Our repair process in Wellington has four parts. You describe the problem and send photos. We price the visit and confirm it in writing. The engineer attends, carries out the agreed work and quotes anything additional before doing it. You then receive a written report on the condition of the equipment and the work completed, which is useful for insurers, inspectors and your own planning.
Do dock shelters and seals fall under PUWER?
Yes. Dock shelters and seals are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Shelter and seal damage is often treated as a comfort or energy issue, but some faults are safety issues too:
- loose head curtains, top pads or fixings that could fall;
- bent or broken frame arms with sharp edges at head height;
- wet or icy dock floors caused by gaps around the trailer;
- electrical faults on inflatable shelter blowers.
The regulator is HSE in Great Britain and HSENI in Northern Ireland. Including shelters and seals in planned maintenance, and recording what is found, shows they are being kept in a safe condition. Problems found during servicing are quoted as repairs before any work is done.
Why is my dock shelter or seal letting in draughts?
A dock shelter or seal lets in draughts when the material that should press against the trailer is torn, worn, too short or no longer in the right place. Daylight around a docked trailer is the clearest sign.
- Torn or shrunk curtains: side curtains no longer overlap the trailer sides.
- Short head curtain: taller trailers than the shelter was sized for leave a gap across the top.
- Flattened seal pads: foam that has lost its spring no longer closes the gap.
- Worn pad covers: exposed foam soaks up water and breaks down faster.
- Bent frame: a retractable shelter frame that no longer returns square.
- Airbag or blower fault: inflatable shelters that inflate slowly or lose pressure.
- Trailer position: off-centre parking or worn bumpers that let trailers crush one side.
On chilled docks, gaps also show up as condensation, ice on the dock floor or frost around the door.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
Checks made while we are on site
- Dock bumpers for missing rubber or loose fixings
- Shelter curtains, frames and side pads for tears
- Vehicle restraint engagement and its signal sequence
- Previous service and inspection records, where available
- Anti-fall device on upward-opening doors
- Wiring, isolators and motor performance under load
Options to discuss
Frame repairs
Straightening or replacing bent arms, springs and frames on retractable shelters damaged by off-centre trailers, so the shelter returns square after each docking.
Airbag and blower repairs
Repairing or replacing torn airbags, failed blower motors and controls on inflatable shelters so the bags inflate fully and seal around the trailer again.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Wellington. Planning and Building Regulations questions are never assumed either way: we check what applies before any work starts, so you know before work is booked.
Questions about dock shelter and seal repairs in Wellington
Can you repair all makes of loading bay equipment?
We work on common makes and types of doors, dock levellers, shelters, seals and restraints. Parts availability varies, particularly for older or discontinued equipment, so it helps to send the make, model and photos of any data plates from your site in Wellington. If original parts are not available, we tell you and price the alternatives, including replacement where that makes more sense.
How is a repair or service visit in Wellington priced?
Repair and service visits are chargeable, and the price is agreed in writing before anyone attends. For dock shelter and seal repairs, the guide budget is £380 to £1,800 per repair, excluding VAT. The exact figure depends on the fault, parts, access and timing. If the engineer finds further work on the day, it is quoted for your approval before it is carried out.
Can you take over our existing loading bay maintenance arrangement?
Yes. Send us a list of the equipment at your Wellington site, with makes, models and approximate ages if known, plus recent service or inspection reports. We will propose a planned maintenance schedule and price it per item per visit. The first visit records the condition of everything, so you have a clear starting point for future servicing.
How is the price for a shelter or seal repair agreed?
You describe the damage and send photos, and we agree the visit price in writing before anyone attends. For made-to-measure parts that may include a measuring visit. Any extra work found on site is quoted and only carried out once you approve it.
Can worn dock seal covers be replaced without new foam?
Often, yes. If the foam inside a seal pad still springs back, a new cover can be fitted over it. If the foam has stayed compressed or soaked up water, the pad is usually replaced complete. Photos of the pads, front and side, help us judge which applies.
Dock shelter and seal repairs near Wellington
We also cover towns near Wellington, including Telford (3 miles), Shrewsbury (10 miles) and Stafford (18 miles). Each has its own page with the same services and process.
Other loading bay services in Wellington
Full guide to dock shelter and seal repairs · Everything we do in Wellington
Start your enquiry for Wellington through the quote tool. A few photos and approximate sizes help us respond with something useful.