- Location
- Inverness, Highlands
- Main postcode district
- IV2
- Nearby (straight line)
- Dingwall (11 miles), Nairn (15 miles) and Forres (24 miles)
- Visit pricing
- Agreed in writing before we attend
Dock shelter and seal repair covers restoring the weather seal around a docked trailer. Typical work includes replacing torn side and head curtains, worn foam seal pads and their covers, top pads and guide strips, repairing or replacing airbags and blowers on inflatable shelters, and straightening or replacing bent shelter frames, so the bay closes the gap between building and trailer again.
Is this right for your site in Inverness?
Exposed yards in Inverness that catch strong winds can tear shelter curtains or strain frames, letting weather into the dock until parts are replaced. Older retractable shelters on estates around Inverness can often be refurbished with new curtains and pads rather than replaced, provided the frame is still sound.
If tenants change at a unit in Inverness, checking the shelters and seals is sensible, because a new fleet may not suit the old curtain sizes.
A chargeable visit, a price agreed in advance and a written report afterwards: that is our approach to dock shelter and seal repairs in Inverness. Photos of the fault, sent before the visit, help us diagnose it and bring suitable parts. Should the job turn out bigger than expected, the extra work is quoted and approved by you before it happens, so there are no surprises on the invoice.
Do dock shelters and seals fall under PUWER?
Yes. Dock shelters and seals are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Shelter and seal damage is often treated as a comfort or energy issue, but some faults are safety issues too:
- loose head curtains, top pads or fixings that could fall;
- bent or broken frame arms with sharp edges at head height;
- wet or icy dock floors caused by gaps around the trailer;
- electrical faults on inflatable shelter blowers.
The regulator is HSE in Great Britain and HSENI in Northern Ireland. Including shelters and seals in planned maintenance, and recording what is found, shows they are being kept in a safe condition. Problems found during servicing are quoted as repairs before any work is done.
What happens on site during a shelter or seal repair?
During a shelter or seal repair the bay is closed to trailers while the engineer works from the yard, often using access equipment for the head curtain and top pad. Neighbouring bays can usually keep working, although access equipment may need space in front of them.
- Measure: where parts are made to measure, the shelter or seal is measured first and the parts ordered.
- Close the bay: no trailer on the dock and the yard area coned off.
- Isolate: on inflatable shelters, the blower supply is isolated and locked off.
- Replace parts: old curtains, pads or airbags are removed and new ones fitted, with frames straightened or replaced as agreed.
- Check the seal: overlap and compression are checked, with a trailer docked if one is available.
It helps if you can provide photos with a trailer docked, yard space for access equipment, a contact who can arrange electrical isolation and an agreed time when the bay can be released.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
Bay checks on a repair or service visit
- Pit frame welds, platform cracks and structural damage
- Control panels, push buttons and emergency stops
- Dock bumpers for missing rubber or loose fixings
- Track alignment, rollers and wall fixings
- Vehicle restraint engagement and its signal sequence
- Hydraulic oil level, hoses and cylinders for leaks
Options to discuss
Curtain replacement
New side and head curtains for retractable shelters, made to measure in hard-wearing coated fabric, with slits and overlaps set to suit the trailers you receive.
Top pad and guide strip replacement
Renewing head pads, top seals and high-visibility guide strips that close the gap above the trailer and help drivers line up on the bay.
What do the rules in Scotland mean for the work?
HSE is the workplace safety regulator in Scotland. At a loading bay in Inverness, doors need to satisfy regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, dock equipment must be kept safe under PUWER, and drivers must be prevented from pulling away too early. We check what applies before any work starts.
Questions about dock shelter and seal repairs in Inverness
What information helps before a repair visit?
Photos or a short video of the fault are the most useful thing you can send, along with the make and model from the data plate, a description of what happens when the equipment is operated and any error codes. For a site in Inverness, also tell us about access, parking and site rules. With that, we can price the visit and bring the likely parts.
Do you cover the Highlands for dock shelter and seal repairs?
Yes. We take on dock shelter and seal repairs for sites in Inverness and throughout the Highlands. Each visit is arranged in advance, with the price agreed in writing before anyone attends. Specialist service engineers working under our management carry out the work, and we remain your point of contact from the first call to the written report.
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
How is the price for a shelter or seal repair agreed?
You describe the damage and send photos, and we agree the visit price in writing before anyone attends. For made-to-measure parts that may include a measuring visit. Any extra work found on site is quoted and only carried out once you approve it.
Can worn dock seal covers be replaced without new foam?
Often, yes. If the foam inside a seal pad still springs back, a new cover can be fitted over it. If the foam has stayed compressed or soaked up water, the pad is usually replaced complete. Photos of the pads, front and side, help us judge which applies.
Dock shelter and seal repairs near Inverness
If your site is not in Inverness itself, it may be near one of these: Dingwall (11 miles), Nairn (15 miles) and Forres (24 miles). Pick the closest.
Other loading bay services in Inverness
Full guide to dock shelter and seal repairs · Everything we do in Inverness
Use the quote tool to tell us about the doors, levellers or shelters at your Inverness site, and we will be in touch to arrange the next step.