- Location
- Andover, Hampshire
- Main postcode district
- SP10
- Nearby (straight line)
- Winchester (13 miles), Newbury (15 miles) and Salisbury (16 miles)
- Visit pricing
- Agreed in writing before we attend
Dock shelter and seal repair covers restoring the weather seal around a docked trailer. Typical work includes replacing torn side and head curtains, worn foam seal pads and their covers, top pads and guide strips, repairing or replacing airbags and blowers on inflatable shelters, and straightening or replacing bent shelter frames, so the bay closes the gap between building and trailer again.
Why do sites in Andover choose this?
Multi-bay sites near Andover often find several shelters in similar condition, so measuring and replacing curtains across the dock in one programme can reduce costs. Inflatable shelters at food sites in Andover depend on blowers and airbags working properly, and a slow-inflating shelter is worth checking before it fails.
If tenants change at a unit in Andover, checking the shelters and seals is sensible, because a new fleet may not suit the old curtain sizes.
When something stops working at a loading bay in Andover, contact us with a description and, ideally, photos. We will confirm the cost of the visit in writing before booking anyone. If the engineer finds the problem goes further than expected, you receive a quote for the additional work and decide whether to proceed. Every visit is followed by a written report you can keep with your maintenance records.
Why is my dock shelter or seal letting in draughts?
A dock shelter or seal lets in draughts when the material that should press against the trailer is torn, worn, too short or no longer in the right place. Daylight around a docked trailer is the clearest sign.
- Torn or shrunk curtains: side curtains no longer overlap the trailer sides.
- Short head curtain: taller trailers than the shelter was sized for leave a gap across the top.
- Flattened seal pads: foam that has lost its spring no longer closes the gap.
- Worn pad covers: exposed foam soaks up water and breaks down faster.
- Bent frame: a retractable shelter frame that no longer returns square.
- Airbag or blower fault: inflatable shelters that inflate slowly or lose pressure.
- Trailer position: off-centre parking or worn bumpers that let trailers crush one side.
On chilled docks, gaps also show up as condensation, ice on the dock floor or frost around the door.
Should I repair my dock shelter or change to a different type?
Repair is usually right when the shelter or seal still suits your trailers and the damage is wear and tear. Changing type is worth considering when the same damage keeps recurring because the equipment no longer suits the vehicles arriving.
- Repair: curtains torn by normal use, worn pad covers, a failed blower or a single bent frame arm.
- Resize: head curtains or pads that are too short for taller trailers now in your fleet.
- Seal to shelter: foam seals suit consistent trailer sizes; a mixed fleet or curtain-siders may need a shelter instead.
- Retractable to inflatable: chilled or frozen docks that need a tighter seal around varied trailers.
- Frame type: shelters repeatedly bent by trailers may suit a retractable frame that gives on impact.
Any change of type is quoted separately from the repair. Our guide to dock shelters vs dock seals explains how each type works and which trailers it suits.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What else does the engineer check at the bay?
- Door springs, cables and drums for wear or damage
- Track alignment, rollers and wall fixings
- Dock bumpers for missing rubber or loose fixings
- Previous service and inspection records, where available
- Vehicle restraint engagement and its signal sequence
- Safety edges, photocells and light curtains
Options to discuss
Seal pad refurbishment
Replacing worn foam pads, or just their covers where the foam is still sound, including tougher facings on the areas where trailers rub most.
Top pad and guide strip replacement
Renewing head pads, top seals and high-visibility guide strips that close the gap above the trailer and help drivers line up on the bay.
What do the rules in England mean for the work?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Andover. Planning and Building Regulations questions are never assumed either way: we check what applies before any work starts, so you know before work is booked.
Questions about dock shelter and seal repairs in Andover
Can repairs be carried out outside our working hours?
Yes, by arrangement. Evening, night or weekend visits can be booked so that repairs and servicing at your Andover site cause less disruption to loading. Out-of-hours attendance usually affects the price, so we include it when we agree the visit charge in writing. Tell us your shift pattern and the times when the dock is quietest.
What happens if the engineer finds the equipment unsafe?
If equipment is found to be unsafe, the engineer will tell you straight away and recommend that it is isolated and taken out of use until it is repaired. That is recorded in the written report. We then quote the repair so you can decide how to proceed. Keeping an unsafe door or leveller in service puts people at risk, so we will always raise it.
Can you repair all makes of loading bay equipment?
We work on common makes and types of doors, dock levellers, shelters, seals and restraints. Parts availability varies, particularly for older or discontinued equipment, so it helps to send the make, model and photos of any data plates from your site in Andover. If original parts are not available, we tell you and price the alternatives, including replacement where that makes more sense.
Can repairs help a chilled loading bay?
Yes. Gaps around a docked trailer let chilled air escape and warm, moist air in, which causes condensation and ice on the dock floor. Restoring the curtains, pads or airbags closes those gaps, helping keep the dock drier and safer to work in.
Why do shelter curtains keep tearing?
Shelter curtains usually keep tearing because trailers arrive off-centre, the curtains are too short or tight for the trailers now in use, or worn bumpers let trailers reverse too far in. Fixing the cause, for example with wheel guides or resized curtains, stops repeat damage.
Dock shelter and seal repairs near Andover
Sites close to Andover get the same service, including those in Winchester (13 miles), Newbury (15 miles) and Salisbury (16 miles), with every job run the same way.
Other loading bay services in Andover
Full guide to dock shelter and seal repairs · Everything we do in Andover
For a written price on loading bay work in Andover, request a quote and include photos of the bay if you can.