- Location
- Rutherglen, Lanarkshire
- Main postcode district
- G73
- Nearby (straight line)
- Cambuslang (2 miles), Glasgow (3 miles) and East Kilbride (5 miles)
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
What should sites in Rutherglen consider?
A dedicated chilled fleet serving a site in Rutherglen can be sealed closely with foam pads, at lower cost than fitting an inflatable shelter. Own-fleet distribution sites in Rutherglen, where the same trailers arrive day after day, are well suited to foam dock seals and the tight fit they give.
Older seals at docks in Rutherglen that have been left with split covers can soak up rain, becoming heavy and losing their shape over winter.
If you are planning dock seals for a site in Rutherglen, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
How much do dock seals cost?
A set of dock seals typically costs £1,100 to £2,600 per set, excluding VAT, supply and fit. A set is normally a head pad and two side pads for one bay.
The price depends on:
- Pad size and depth: larger openings and deeper foam cost more.
- Head arrangement: a fixed head pad, or a curtain head for varied trailer heights.
- Cover fabric: heavier coated fabric and replaceable wear pleats last longer.
- Pad shape: tapered side pads that guide the trailer and intrude less into the opening.
- Mounting: fixing direct to masonry, to a steel frame, or to brackets that set the projection.
- Site work: removing old seals, adjusting bumpers and powered access equipment.
Where the foam is still sound, new covers can cost less than new pads, and we will say if that is an option. After a free site survey you receive a fixed written price for the work described.
Why does the gap between the seal and the bumpers matter?
The distance between the face of the seal and the face of the bumpers decides how far the trailer compresses the foam, and getting it right is the difference between a good seal and pads that are crushed or leave gaps.
- Too little projection: the trailer meets the bumpers before it presses the foam enough, leaving gaps at the head and sides.
- Too much projection: the foam is over-compressed, which crushes the pads, strains the fixings and can push the trailer forward as the foam recovers.
- Worn bumpers: let trailers travel further than designed, over-compressing the seal every time.
Correct projection depends on the foam depth and your trailers, so we set it at installation and it should be checked at each service. Keeping dock bumpers in good condition protects both the seal and the leveller from repeated impact.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Temperature requirements for chilled, frozen or ambient goods
- Whether planning, building control or a building warrant may be needed
- Gaps around trailers where heated or chilled air escapes
- Clear opening width and height for each door
- Drainage on recessed or sloping dock approaches
- Lighting inside trailers and at the dock face
Options to discuss
Tapered side pads
Side pads tapered in section so they guide the trailer in and intrude less into the trailer opening, which extends pad and cover life.
Fixed head pad seal
A head pad and two side pads of set depth, the simplest and tightest arrangement where every trailer using the bay is the same height.
Regulations and approvals in Scotland
HSE is the workplace safety regulator in Scotland. At a loading bay in Rutherglen, doors need to satisfy regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, dock equipment must be kept safe under PUWER, and drivers must be prevented from pulling away too early. We check what applies at survey.
Questions about dock seals in Rutherglen
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Rutherglen site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
How do you price dock seals for a site in Rutherglen?
Guide budgets for supply and fit are £1,100 to £2,600 per set, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Is the site survey in Rutherglen free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Do dock seals block access to the trailer?
They can if they are poorly sized. Side pads that sit inside the line of the trailer body intrude into the opening and get in the way of pallets and forklifts. Correctly sized and tapered pads compress against the rear corners and leave the opening clear.
Can just the covers be replaced?
Yes, if the foam is still resilient and dry, new covers can often be fitted over the existing foam, which usually costs less than new pads. Waterlogged or permanently crushed foam should be replaced. Cover replacement is handled as a repair, with the visit price agreed beforehand.
Dock seals near Rutherglen
The same survey, quote and repair service is available in towns around Rutherglen, such as Cambuslang (2 miles), Glasgow (3 miles) and East Kilbride (5 miles).
Other loading bay services in Rutherglen
Full guide to dock seals · Everything we do in Rutherglen
Use the quote tool to tell us about the doors, levellers or shelters at your Rutherglen site, and we will be in touch to arrange the next step.