- Location
- Sandown, Isle of Wight
- Main postcode district
- PO36
- Nearby (straight line)
- Ryde (5 miles), Newport (7 miles) and Cowes (10 miles)
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
Is this right for your site in Sandown?
Weather-exposed bays in Sandown gain the most from a well-fitted seal, since wind and rain otherwise find every gap around the trailer. Heated packing halls next to a dock in Sandown lose less warmth during loading when the gap around each trailer is closed by compressed foam.
Own-fleet distribution sites in Sandown, where the same trailers arrive day after day, are well suited to foam dock seals and the tight fit they give.
Your loading bay stays our responsibility from the survey to the handover. In Sandown, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
How are dock seals fitted to a loading bay?
Dock seals are fixed to the outside wall around the dock door, normally on brackets or a frame that sets their projection, and a set usually takes a few hours to fit. No power supply is needed.
- The wall is checked for sound fixing points, with a frame or spreader plates added on cladding.
- The head pad and side pads are positioned to suit your trailer width and height.
- Projection is set relative to the bumpers, so trailers compress the foam by the right amount.
- Bumpers are checked and, if worn, replaced at the same time.
- A trailer is docked to confirm an even seal along the head and sides.
From you we need the bay taken out of use, a clear area in the yard for powered access equipment and, ideally, one of your usual trailers available at the end of the job so the fit can be checked under real conditions.
How much do dock seals cost?
A set of dock seals typically costs £1,100 to £2,600 per set, excluding VAT, supply and fit. A set is normally a head pad and two side pads for one bay.
The price depends on:
- Pad size and depth: larger openings and deeper foam cost more.
- Head arrangement: a fixed head pad, or a curtain head for varied trailer heights.
- Cover fabric: heavier coated fabric and replaceable wear pleats last longer.
- Pad shape: tapered side pads that guide the trailer and intrude less into the opening.
- Mounting: fixing direct to masonry, to a steel frame, or to brackets that set the projection.
- Site work: removing old seals, adjusting bumpers and powered access equipment.
Where the foam is still sound, new covers can cost less than new pads, and we will say if that is an option. After a free site survey you receive a fixed written price for the work described.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Asbestos register and any other site hazard information
- Control positions, isolators and any existing interlocks
- Wheel guide positions and yard markings for reversing vehicles
- Gaps around trailers where heated or chilled air escapes
- Forklift and pallet truck loads crossing the leveller platform
- Wall and steel structure for door, shelter and bumper fixings
Options to discuss
Tapered side pads
Side pads tapered in section so they guide the trailer in and intrude less into the trailer opening, which extends pad and cover life.
Seal with curtain head
Foam side pads combined with a flexible top curtain that adjusts to trailers of different heights, a halfway point between a seal and a shelter.
Which rules apply in England?
Sites in Sandown fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Sites in and around Sandown are covered by arrangement. There is no charge for the survey or the written quote, and any travel, ferry crossings or overnight stays needed for the installation itself are itemised in the quote, so you see the full price before agreeing.
Questions about dock seals in Sandown
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Sandown, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Can you work alongside our main contractor on a new build in Sandown?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
How do you price dock seals for a site in Sandown?
Guide budgets for supply and fit are £1,100 to £2,600 per set, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Can just the covers be replaced?
Yes, if the foam is still resilient and dry, new covers can often be fitted over the existing foam, which usually costs less than new pads. Waterlogged or permanently crushed foam should be replaced. Cover replacement is handled as a repair, with the visit price agreed beforehand.
Are dock seals suitable for cold stores?
Yes, for cold stores with consistent trailers a dock seal gives a tight fit at a lower cost than an inflatable shelter. The pads must be kept in good condition, because water in the foam can freeze and stiffen it. Mixed fleets at cold stores are often better served by inflatable shelters.
Dock seals near Sandown
Nearby places we cover, measured from Sandown, include Ryde (5 miles), Newport (7 miles) and Cowes (10 miles). Ask if your own town is missing.
Other loading bay services in Sandown
Full guide to dock seals · Everything we do in Sandown
Have photos of the door, leveller or shelter? Send them with your enquiry and we can give a clearer answer for your Sandown site.