- Location
- Pembroke Dock, Dyfed
- Main postcode district
- SA72
- Nearby (straight line)
- Milford Haven (4 miles), Haverfordwest (8 miles) and Carmarthen (30 miles)
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
How does this suit sites in Pembroke Dock?
A dedicated chilled fleet serving a site in Pembroke Dock can be sealed closely with foam pads, at lower cost than fitting an inflatable shelter. Older seals at docks in Pembroke Dock that have been left with split covers can soak up rain, becoming heavy and losing their shape over winter.
Where trailers reverse onto a bay in Pembroke Dock slightly off-centre, tapered side pads and wheel guides help protect the seal from rubbing.
Step one is a survey at your site in Pembroke Dock, which costs nothing and carries no obligation. Step two is a written quote with a fixed price and a clear scope. Step three is installation, scheduled around your operation and carried out by specialist installation engineers working under our management, including evenings or weekends if agreed. Step four is handover, when the equipment is tested in front of you and the paperwork is passed over.
How are dock seals fitted to a loading bay?
Dock seals are fixed to the outside wall around the dock door, normally on brackets or a frame that sets their projection, and a set usually takes a few hours to fit. No power supply is needed.
- The wall is checked for sound fixing points, with a frame or spreader plates added on cladding.
- The head pad and side pads are positioned to suit your trailer width and height.
- Projection is set relative to the bumpers, so trailers compress the foam by the right amount.
- Bumpers are checked and, if worn, replaced at the same time.
- A trailer is docked to confirm an even seal along the head and sides.
From you we need the bay taken out of use, a clear area in the yard for powered access equipment and, ideally, one of your usual trailers available at the end of the job so the fit can be checked under real conditions.
Why does the gap between the seal and the bumpers matter?
The distance between the face of the seal and the face of the bumpers decides how far the trailer compresses the foam, and getting it right is the difference between a good seal and pads that are crushed or leave gaps.
- Too little projection: the trailer meets the bumpers before it presses the foam enough, leaving gaps at the head and sides.
- Too much projection: the foam is over-compressed, which crushes the pads, strains the fixings and can push the trailer forward as the foam recovers.
- Worn bumpers: let trailers travel further than designed, over-compressing the seal every time.
Correct projection depends on the foam depth and your trailers, so we set it at installation and it should be checked at each service. Keeping dock bumpers in good condition protects both the seal and the leveller from repeated impact.
The same published guide range applies across Wales; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Lighting inside trailers and at the dock face
- Dock height and the mix of trailers you load
- Headroom above the opening and which track type will suit it
- Control positions, isolators and any existing interlocks
- Access for deliveries, cranes or lifting equipment during installation
- Wind exposure at the dock, which affects door and shelter choice
Options to discuss
Seal with curtain head
Foam side pads combined with a flexible top curtain that adjusts to trailers of different heights, a halfway point between a seal and a shelter.
Fixed head pad seal
A head pad and two side pads of set depth, the simplest and tightest arrangement where every trailer using the bay is the same height.
Regulations and approvals in Wales
HSE regulates workplace safety in Wales. Loading bays in Pembroke Dock need doors that meet regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, work equipment maintained under PUWER, and safeguards that stop vehicles leaving the dock too early. We check what applies at survey and build those measures into the design.
Questions about dock seals in Pembroke Dock
What details do you need from us to quote for dock seals?
To get started, send the site address in Pembroke Dock, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
How long does installation take at a site in Pembroke Dock?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Is the site survey in Pembroke Dock free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Are dock seals suitable for cold stores?
Yes, for cold stores with consistent trailers a dock seal gives a tight fit at a lower cost than an inflatable shelter. The pads must be kept in good condition, because water in the foam can freeze and stiffen it. Mixed fleets at cold stores are often better served by inflatable shelters.
Can dock seals handle trailers of different heights?
Only within a limited range. A fixed head pad seals well on trailers of one height but leaves gaps over lower ones and can be crushed by taller ones. A seal with a flexible curtain head copes better with varied heights, and for very mixed fleets a shelter is usually the better option.
Dock seals near Pembroke Dock
Close neighbours of Pembroke Dock with their own pages here: Milford Haven (4 miles), Haverfordwest (8 miles) and Carmarthen (30 miles). Choose one to see coverage details for that town.
Other loading bay services in Pembroke Dock
Full guide to dock seals · Everything we do in Pembroke Dock
Get in touch about loading bay doors and dock equipment in Pembroke Dock: call, email or use the quote tool.