- Location
- Seaham, County Durham
- Main postcode district
- SR7
- Nearby (straight line)
- Houghton-le-Spring (5 miles), Sunderland (5 miles) and Peterlee (5 miles)
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
Why do sites in Seaham choose this?
Hygiene-sensitive sites in Seaham, such as food processors, can use dock seals to reduce the gaps through which dust and pests might enter during loading. Own-fleet distribution sites in Seaham, where the same trailers arrive day after day, are well suited to foam dock seals and the tight fit they give.
Weather-exposed bays in Seaham gain the most from a well-fitted seal, since wind and rain otherwise find every gap around the trailer.
A single contact at Loading Bay Doors handles your project in Seaham from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
Why does the gap between the seal and the bumpers matter?
The distance between the face of the seal and the face of the bumpers decides how far the trailer compresses the foam, and getting it right is the difference between a good seal and pads that are crushed or leave gaps.
- Too little projection: the trailer meets the bumpers before it presses the foam enough, leaving gaps at the head and sides.
- Too much projection: the foam is over-compressed, which crushes the pads, strains the fixings and can push the trailer forward as the foam recovers.
- Worn bumpers: let trailers travel further than designed, over-compressing the seal every time.
Correct projection depends on the foam depth and your trailers, so we set it at installation and it should be checked at each service. Keeping dock bumpers in good condition protects both the seal and the leveller from repeated impact.
How much do dock seals cost?
A set of dock seals typically costs £1,100 to £2,600 per set, excluding VAT, supply and fit. A set is normally a head pad and two side pads for one bay.
The price depends on:
- Pad size and depth: larger openings and deeper foam cost more.
- Head arrangement: a fixed head pad, or a curtain head for varied trailer heights.
- Cover fabric: heavier coated fabric and replaceable wear pleats last longer.
- Pad shape: tapered side pads that guide the trailer and intrude less into the opening.
- Mounting: fixing direct to masonry, to a steel frame, or to brackets that set the projection.
- Site work: removing old seals, adjusting bumpers and powered access equipment.
Where the foam is still sound, new covers can cost less than new pads, and we will say if that is an option. After a free site survey you receive a fixed written price for the work described.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Forklift and pallet truck loads crossing the leveller platform
- Whether planning, building control or a building warrant may be needed
- Wall and steel structure for door, shelter and bumper fixings
- Asbestos register and any other site hazard information
- How drivers are prevented from pulling away too early
- Lighting inside trailers and at the dock face
Options to discuss
Replaceable wear pleats
Sacrificial fabric strips on the pad faces that take the rubbing from trailers and can be replaced without changing the whole cover.
Seal with curtain head
Foam side pads combined with a flexible top curtain that adjusts to trailers of different heights, a halfway point between a seal and a shelter.
Which rules apply in England?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Seaham. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock seals in Seaham
Is VAT included in your guide prices for dock seals?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in County Durham as everywhere else: for dock seals, it is £1,100 to £2,600 per set, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Can you work alongside our main contractor on a new build in Seaham?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Seaham, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Do dock seals block access to the trailer?
They can if they are poorly sized. Side pads that sit inside the line of the trailer body intrude into the opening and get in the way of pallets and forklifts. Correctly sized and tapered pads compress against the rear corners and leave the opening clear.
Can just the covers be replaced?
Yes, if the foam is still resilient and dry, new covers can often be fitted over the existing foam, which usually costs less than new pads. Waterlogged or permanently crushed foam should be replaced. Cover replacement is handled as a repair, with the visit price agreed beforehand.
Dock seals near Seaham
We also cover towns near Seaham, including Houghton-le-Spring (5 miles), Sunderland (5 miles) and Peterlee (5 miles). Each has its own page with the same services and process.
Other loading bay services in Seaham
Full guide to dock seals · Everything we do in Seaham
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Seaham.