- Location
- Marlow, Buckinghamshire
- Main postcode district
- SL7
- Nearby (straight line)
- Maidenhead (4 miles), High Wycombe (4 miles) and Slough (9 miles)
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
Is this right for your site in Marlow?
Own-fleet distribution sites in Marlow, where the same trailers arrive day after day, are well suited to foam dock seals and the tight fit they give. Hygiene-sensitive sites in Marlow, such as food processors, can use dock seals to reduce the gaps through which dust and pests might enter during loading.
Before recommending seals for a bay in Marlow, we check how consistent your trailers are, because mixed fleets are usually better served by a shelter.
If you are planning dock seals for a site in Marlow, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
How can dock seal pads be made to last longer?
Dock seal pads last longer when trailers arrive straight and stop at the right point, because most wear comes from trailers rubbing against the covers or pressing too far into the foam. Covers usually wear first, and the foam inside can outlast them.
- Replaceable wear pleats: sacrificial strips on the pad faces take the abrasion and can be swapped cheaply.
- Wheel guides and dock lights: help drivers reverse squarely into the centre of the bay.
- Bumper maintenance: keeps compression within design limits.
- Tapered side pads: guide trailers in and reduce rubbing on the pad edges.
- Driver briefings: regular hauliers who know the bay damage it less.
When covers split, replacing them promptly stops rain soaking into the foam, which makes it heavy, slow to recover and prone to freezing in winter.
How are dock seals fitted to a loading bay?
Dock seals are fixed to the outside wall around the dock door, normally on brackets or a frame that sets their projection, and a set usually takes a few hours to fit. No power supply is needed.
- The wall is checked for sound fixing points, with a frame or spreader plates added on cladding.
- The head pad and side pads are positioned to suit your trailer width and height.
- Projection is set relative to the bumpers, so trailers compress the foam by the right amount.
- Bumpers are checked and, if worn, replaced at the same time.
- A trailer is docked to confirm an even seal along the head and sides.
From you we need the bay taken out of use, a clear area in the yard for powered access equipment and, ideally, one of your usual trailers available at the end of the job so the fit can be checked under real conditions.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Wheel guide positions and yard markings for reversing vehicles
- Yard gradient and the slope of the approach to the dock
- Bumper position and wear or damage on the dock face
- Traffic routes for vehicles and separation of pedestrians
- Headroom above the opening and which track type will suit it
- Access for deliveries, cranes or lifting equipment during installation
Options to discuss
Replaceable wear pleats
Sacrificial fabric strips on the pad faces that take the rubbing from trailers and can be replaced without changing the whole cover.
Seal with curtain head
Foam side pads combined with a flexible top curtain that adjusts to trailers of different heights, a halfway point between a seal and a shelter.
What do the rules in England mean for the work?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Marlow. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock seals in Marlow
What details do you need from us to quote for dock seals?
To get started, send the site address in Marlow, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Is the site survey in Marlow free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Is VAT included in your guide prices for dock seals?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Buckinghamshire as everywhere else: for dock seals, it is £1,100 to £2,600 per set, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
How can I tell if seal projection is wrong?
Look at the pads with a trailer docked. Daylight around the head or sides suggests too little compression, while pads squashed flat or bulging around the trailer suggest too much. Worn bumpers are a common cause, and both can be checked at a planned service.
Are dock seals suitable for cold stores?
Yes, for cold stores with consistent trailers a dock seal gives a tight fit at a lower cost than an inflatable shelter. The pads must be kept in good condition, because water in the foam can freeze and stiffen it. Mixed fleets at cold stores are often better served by inflatable shelters.
Dock seals near Marlow
Other towns within reach of Marlow on our coverage list include Maidenhead (4 miles), High Wycombe (4 miles) and Slough (9 miles), all covered on the same terms.
Other loading bay services in Marlow
Full guide to dock seals · Everything we do in Marlow
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Marlow site.