- Location
- Yeadon, West Yorkshire
- Main postcode district
- LS19
- Nearby (straight line)
- Guiseley (1 mile), Horsforth (3 miles) and Shipley (4 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Is this right for your site in Yeadon?
Shelters and seals at sites near Yeadon last longer when wheel guides keep trailers centred, because off-centre parking is a common cause of torn curtains. Warehouses in Yeadon loading deep trailers by forklift often find the back of the load hard to see without a dock light reaching into the trailer.
A landlord preparing a unit in Yeadon for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical.
We never ask you to commit before you have a fixed price. A free survey at your Yeadon site comes first, followed by a written quote. When the order goes ahead, we plan the installation around your operation, book any out-of-hours working you need and manage the specialist installation engineers on site. The job ends with a full test, a run-through for the people who will use the equipment and a set of handover documents.
How much do dock lights and wheel guides cost?
Dock lights and wheel guides typically cost £280 to £950 per item, supplied and fitted, excluding VAT, where an item is one dock light or one wheel guide. A standard LED swing-arm light usually sits in the lower half of the range; long, heavy-section or cast-in guides sit towards the top.
What moves the price:
- Light specification: arm length, LED head output, protective guarding and whether a low-voltage supply is needed.
- Power: the distance to a suitable supply and how the cable is contained.
- Guide length and section: longer guides and heavier steel cost more.
- Yard surface: sound concrete takes anchors directly; tarmac usually needs a concrete base first, priced after survey.
- Number of bays: fitting several bays in one visit lowers the cost per item.
These are guide budgets. After a free site survey we send a written quote, which is the fixed price. VAT is added at the standard rate.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Dock height and the mix of trailers you load
- Whether planning, building control or a building warrant may be needed
- Scope to convert ground-level doors into docks or add lift tables
- How drivers are prevented from pulling away too early
- Gaps around trailers where heated or chilled air escapes
- Lighting inside trailers and at the dock face
Options to discuss
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Low-voltage dock light
A swing-arm light fed through a transformer mounted nearby, for sites that prefer a reduced voltage at the lamp head. Same reach and folding action as a mains light.
Which rules apply in England?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Yeadon. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock lights and wheel guides in Yeadon
How do you price dock lights and wheel guides for a site in Yeadon?
Guide budgets for supply and fit are £280 to £950 per item, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Do you cover Yeadon for dock lights and wheel guides?
Yes. We take on dock lights and wheel guides for businesses in Yeadon and across West Yorkshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Is VAT included in your guide prices for dock lights and wheel guides?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in West Yorkshire as everywhere else: for dock lights and wheel guides, it is £280 to £950 per item, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Where should a dock light be mounted?
A dock light is mounted inside the building beside the door opening, high enough to swing over the leveller and into the trailer. It must fold back flat against the wall, clear of the door tracks and the forklift route, so it is not struck when the bay is not in use.
Dock lights and wheel guides near Yeadon
Close neighbours of Yeadon with their own pages here: Guiseley (1 mile), Horsforth (3 miles) and Shipley (4 miles). Choose one to see coverage details for that town.
Other loading bay services in Yeadon
Full guide to dock lights and wheel guides · Everything we do in Yeadon
For a written price on loading bay work in Yeadon, request a quote and include photos of the bay if you can.