- Location
- Sudbury, Suffolk
- Main postcode district
- CO10
- Nearby (straight line)
- Colchester (13 miles), Haverhill (13 miles) and Braintree (13 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Why do sites in Sudbury choose this?
Tight yards in Sudbury where drivers reverse between parked trailers or around buildings make wheel guides especially useful for getting the trailer straight first time. A landlord preparing a unit in Sudbury for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical.
Warehouses in Sudbury loading deep trailers by forklift often find the back of the load hard to see without a dock light reaching into the trailer.
Here is what happens after you contact us about a site in Sudbury. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
Should wheel guides be bolted down or cast in?
Wheel guides are bolted down on an existing sound concrete yard and cast in where new concrete is being laid. Both give a strong fixing; the choice depends on whether the yard is being resurfaced.
- Bolt-down guides: steel tube or channel fixed with resin anchors. Quick to fit to existing bays and easy to replace if damaged.
- Cast-in guides: set into fresh concrete with embedded anchors, suited to new-build docks and conversions.
- Flared entry: an angled lead-in at the yard end catches the wheel early and steers it into line.
- Finish: typically galvanised, or painted yellow and black so drivers can see them in mirrors.
Guides are set out to suit the track width of the trailers you receive, centred on the leveller, and long enough to straighten the trailer before it reaches the bumpers. Tarmac is usually too soft to hold anchors, so a concrete strip or base is laid first. Our guide to choosing dock bumpers and wheel guides covers layout in more depth.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Condition of any existing leveller pit, kerb angles and pit drainage
- Escape routes and pedestrian doors close to the bay
- Forklift and pallet truck loads crossing the leveller platform
- How often each door cycles during a typical shift
- Power supply at each bay, including three-phase availability
- Headroom above the opening and which track type will suit it
Options to discuss
Bolt-down wheel guides
Steel tube or channel guides fixed with resin anchors into an existing concrete apron, typically galvanised or painted in high-visibility colours for drivers using mirrors.
LED swing-arm dock light
An LED head on a swing arm beside the door, swung into the trailer during loading and folded back flat against the wall when the bay is closed.
Planning, building control and safety law in England
Workplace safety in England is regulated by HSE. For a loading bay in Sudbury, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about dock lights and wheel guides in Sudbury
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Sudbury site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Is the site survey in Sudbury free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Can you work alongside our main contractor on a new build in Sudbury?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Are LED dock lights better than older lamps?
LED dock lights are generally the better choice. They run much cooler, so there is less risk of heat damage to goods or packaging close to the head, they cope well with vibration, and they reach full brightness straight away. They also use less electricity for the same light, although savings depend on how long the lights are on.
Do wheel guides damage tyres?
Correctly spaced wheel guides should not damage tyres. They are set slightly wider than the trailer track so the tyre only brushes the guide when the trailer is off line, and a flared entry stops tyres hitting the end. Guides that are bent or set too narrow should be corrected.
Dock lights and wheel guides near Sudbury
Close neighbours of Sudbury with their own pages here: Colchester (13 miles), Haverhill (13 miles) and Braintree (13 miles). Choose one to see coverage details for that town.
Other loading bay services in Sudbury
Full guide to dock lights and wheel guides · Everything we do in Sudbury
Get in touch about loading bay doors and dock equipment in Sudbury: call, email or use the quote tool.